JENOLITE Rust Converter Spray | 400ml | RUST TREATMENT & RUST INHIBITOR | Fast Acting Epoxy Based Rust Converter For Metal | Converts Rust Into Stable, Ready-to-Paint Surface

Excellent product, easy to use and works quickly. I was previously sanding off rust by hand prior to painting and this has saved me a vast amount of time. Pictured is a carriage pole I am refurbishing, tested area on the left, untreated on the right. I will be buying it again!

This Jenolite Rust Converter Spray is really good. I was surprised how fast this spray worked on my rusty Ford Fusion underneath. You don't really have to paint any underseal paint on top of it, but i always make my special mix of paints and black gasket sealant mixed up with some paint thinners, works a treat everytime. I strongly suggest you wear protective glasses, face mask, gloves and some old clothes before you start painting. Try to remove all the bad rust, either with a good wire brush or one that fits to a drill or grinder. Remove all grease and dirt before spraying the Converter Spray. This isn't cheap stuff but it does the job on any rusted item's. Rust is just like a 'Cancer' it spreads if untreated. Always look after your vehicles and they will last for years. I highly recommend this "JENOLITE RUST CONVERTER", Just a shame it's so expensive..

Good quality spray. Can make metal go black on contact.

After a bit of research into what product was best for my needs, I opted for Jenolite Rust Converter Spray. Stone chips had broken through the paint around the arch areas of my campervan, looking unsightly. A quick rub down on the affected area with 80 grit oxide paper back to clean metal, masking tape applied to avoid any overspray, then follow the instructions on the can - shake contents for a few mins, then apply from around 25cms, leave to dry circa 15 mins, then re-apply. It's clear initially, but as it gets to work it turns black, after 2 coats a thick protective layer is formed, after fully dry / cured the epoxy feels tough and has good coverage, I'm letting it fully harden over this week, and will look to apply a top coat of colour matched spray paint, and clear lacquer top coat to blend it in, and will then apply 2 coats of the Jenolite on top of the colour matched spray paint for added protective layer as it is clear. Good product, good performance straight out the tin with minimal prep, instructions are simple to follow.

Easy to apply. Fast drying and works well. Great coverage per can. For reference I did two coats on all rear suspension and rear floor pan of a vw Tiguan with 2 1/2 cans

Does the job brill product well recommend

i thought my days of getting under a car were over. I had a fiat in the 70's so when the garage told me there was rust underneath my 13 year old mini i decided to act. Jacking the car up using a plank and the kerb i was able to crawl underneath safely and spy out the rusty bits. you should use a wire brush to get rid of the loose bits - which i tried to do where i could reach. Because this stuff is a spray i was able to coat everywhere i could see even if i were spraying through small gaps. Once applied the surface turns silvery. you do need to do 3 coats with at least a 20 minute gap. it does not state the coverage on the tin - i only had a few bits to do - around 1 square m (10 sq feet). i used the bitumen spray to cover after a 2 day wait - the bitumen coverage is much more - i feel i used about 1/4 to 1/3 of that to the whole tin of rust converter. i cannot give this a 5 star rating as the proof of it will be in a couple of years not weeks.

This is a great product. I recently used it to treat the underbody of my 20 year old Ford Focus. It provided excellent coverage, and a good surface for paint to adhere to. However, as always with any type of paint/protector product, the preparation is every bit as important as the product itself. First, use a wire wheel and/or sandpaper to remove all the loose rust and dirt. Then use brake cleaner and a cloth to thoroughly clean and dry the area, and remove any grease. Only then should you apply the rust converter spray. Under these conditions, the spray adheres well to the surface, and forms an impenetrable epoxy barrier which stops rust developing further. Once this is dry, you can then paint it with the colour of your choice.

Funciona perfectamente

Follow the directions carefully. Spray OUTSIDE. Prepare to leave whatever you're spraying OUTSIDE for a minimum of 2 days with any sprayed areas OPEN. The fumes will go away, but they are very strong. The warnings on the can make this very clear. I used it to spray rust in the spare tire well in the trunk of my car which didn't rust due to water intrusion ... nooooo - it was mice that made their home in there. Their 'biological leavings' ate through the paint and caused rust. Also applied to other various areas that made light surface rust after sanding in the process of repainting a car. Coats really nicely, had no problem putting an epoxy primer over the top of this stuff (I gave it a week). Worked exactly as advertised. The more work you put into preparing the surface, the better the product will work.

Sehr gutes Produkt!

Schnelle lieferung, EXTRA gute qualität !

super produit ! forme une couche de résine qui durcit en séchant. acheté pour couvrir des soudures avant peinture, le rendu est super propre. peut s'appliquer généreusement sur un support horizontal, mais par petites couches sur un support vertical pour éviter les coulures. un petit peu cher certes, mais généralement les produits contenant de l'epoxy ne sont pas donnés .