Lykus HC-4410 Waterproof Hard Case with Customizable Foam Insert, Interior Size 17.32x11.42x4.72 in, Suitable for up to 16" Laptop,Starlink Mini,Keyboard,Drill,Audio Mixer,Mic,Flashlight,and More

I purchased this case to house my two suppressors and Nieson Device accessories. The center foam was hollowed out to accommodate them with plenty of room for accessories. This would also make a great case for cameras or small optics. Extremely sturdy and protects from rough handling.

This is a very sturdy case. It holds a good amount of stuff. I have a camera, extra batteries, a DJI Osmo pocket 3, and all the ND filters and accessories that I could want in it. It takes a bit of time to cut out the foam to fit what you want to put in it (especially if it has a lot of odd curves), but if done right it will definitely protect your equipment. I had mine on the upper shelf of my closet and somehow it fell down about 7-8ft straight onto the hardwood floor and everything in it was perfectly fine. The case didn't even have a scratch on it either! Very well made and a good alternative to a pelican case if you don't want to spend a ton of money.

I was in need of a hard case for my ROG Gaming laptop. Most cases for laptops are not sized for the larger gaming laptops. This was a perfect fit! I have enough room to house the laptop on the bottom layer of foam. The cut to fit foam in the middle provides support around the laptop and the remaining foam goes on top. I cut out the bottom foam two house the power brick and did the same for the top layer in order to house a mouse and the power cord for the power brick. All in all, a great product and easily modified.

This case is a good size for holding 2 Canon EOS camera bodies along with 3 lenses. It is of sturdy construction and materials like many similar cases that are far more expensive. The foam padding is good quality pick & pluck that should keep delicate cargo safe. All in all, I feel this was a good investment and I will look to Lykus for additional cases as my needs grow.

This is a somewhat pricey hard case but it is well made and the precut foam appears to be first rate. It just lacks being able to open to 180°.

I am happy with my purchase. It's just the size I was looking for, and about as big as you'd want a case for carrying by hand. The foam is of good quality, and the case is solid and protective.

This case is very well made and will provide excellent protection for anything you put inside. I highly recommend it!

I ordered this case to hold several telescope eyepieces that were starting to exceed the capacity of a smaller case that came as a set with some of the eyepieces. I'm impressed with the quality of the case. The fit and finish of the case is great, the body feels substantial, the latches work flawlessly, and the pickable foam has two pickable layers to give you even more ability to customize (although I only need to pick through one layer to meet my needs). If I need to get another one in the future, I'm going to look at this company first.

Det var jätte bra…

Perfect for my Alienware area 51 18" Laptop. I did need to trim half a square nearest to the outside edge bottom part, but it does fit. Make sure to measure by placing your laptop (or whatever items your placing inside the case) on top of the foam and mark it. I used chalk for this. The box itself is the perfect size for my 18"Alienware Area 51. I think if it were any bigger it may be too big, and be encomersome. So this box is perfect. For the pre cut foam I used a tooth pick to gently cut into the edges that were a little tight to gently tear. I also used a Cutting Blade like a Stanley knife to slowly cut into half the pre cut square, so I was able to remove just half of the square, leaving half behind to make the fit better.

I bought this as case for hoverair X1 selfie dron. When all padding removed, drone fits perfectly. I am not putting spare battery there.

Mooi kleine opbergbox van hard kunststof. Zowel in de boven- als de onderzijde een 5 mm dikke schuimlaag en onderin, daarboven op de 2 cm dikke aanpasbare schuimlaag. Al met al een mooie beschermplaats voor nauwkeurige instrumenten.

What a nice container. I was pleasantly surprised. The case looks sturdy en the seals look like good quality rubber. The center foam is easy to cut. The case also contains an additionale slim foam in the lid and on the bottom. I use it as a battery case for a bug-out-pack. I have inserted the following batteries: 6x AAA, 6x AA, 2x CR123, 1x 18650.