Pilot Arc Plasma Cutter, [Large LED Display][Air Sensor] 50A Plasma Cutter Machine 110/220V Dual Voltage, 1/2'' Clean Cut 3/4 Inch Max Cut, Post Flow Mesh, 2T/4T for Beginners DIY

Folowing up from my last review. Standup company. I was a week outside of the manufacturer's standard 30 day warranty. Contacted bestarc and sent them the same pictures I posted here. Without any questions they sent me a new unit. If this one goes out, I'll just buy a new one and purchase the extended warranty next time. For the weekend hobbiest this unit is more than enough. Wish I could give this 5 stars. When it worked it worked well. Especially for the price. After just 45 days of using it one of the relays soldered into the PCB took a crap and shorted out. All I have predominantly used this machine for is 18-20 gauge sheet steel so its not like I was pulling much power. I didnt purchase an extended warranty, thats my fault. Is what it is. I contacted bestarc directly to see if there is anything they'd be willing to do to help out so if anything comes of it ill update this review accordingly. Pictures to show the issue mentioned.

It definitely works great but I would recommend using it on a 220 plug to cut the materials faster because if you use it on 120 volts it tripped the breaker a lot unless you do five seconds take a break although it’s a very good machine

Let me start by saying I bought this with my.own money. About 20 years ago, I worked in a welding fabrication shop. They had a plasma cutter back then. It cost probably 10 to 20 times what this machine cost and it didn't work nearly as good as this bestarc. Technology has improved tremendously in 20 years. Obviously. I had no idea that such a quality machine could be bought for so little money nowadays. I am no longer a professional fabricator, an amateur at best nowadays. Even so, I was able to put this cutter together and start cutting in minutes. Just hook up the lines and power and air. I didn't even have to mess with the settings much. If it didn't cut I just turned up the air and amps and voila, it cut great. I bought this for one job of installing floor pans in an old jeep and I am really glad I did. It was literally like taking a magic pencil and drawing a cut line on the pan and it just falling out. It was much easier than any other method of cutting. It made trimming the new pan easy as well. If I needed a hole, forget the drill, I just started the arc up and plunged cut a hole. The floor pans where very thin, like 20 gauge so they were easy for this machine to cut. I tried some 1/4 inch plate and had great results as well with a 220v power supply. I wish I would have bought one of these years ago and gave my oxy-acetalyne torch away. This plasma cutter is better in every way as long as you have power. I love it, buy it, you won't regret it. Oh and I didn't even mess one tip up while using it on this job. That says a lot to it design and durability.

For an inexpensive entry level plasma cutter, this is pretty great. Now I will say, it is great as far as it's cutting capabilities and ease of use (and boy do I use it). There are a few reasons for 4 starts and not 5 though. 1. The handle part feels a bit cheap. Still, if you are just a small shop who needs to cut metal on occasion or a weekend warrior like myself, it'll do. If you are a shop doing a lot of metal fabrication, maybe spend a few bucks more on something more durable. 2. It claims to work with a small pancake compressor. I set this up immediately and yes, it does work, however a small pancake compressor is only good for small cuts with breaks in-between for the compressor to refill. I found that to maintain 45 PSI for what I was cutting, I has to set the compressor to 60 PSI and it ran out pretty fast. I changed to my slightly bigger 3 gal Harbor Freight compressor and it was waaaayyy better with the ability to cut for longer periods at a time. Just think of how long each blast will be and make sure you have a compressor that can keep up. For small holes and cuts, the pancake is probably ok. For larger cuts or long use cuts, bigger is better. 3. It can run on 110, but... you know. So I hooked it up to a regular 110 outlet and it worked great for light gauge metal. I worked my way up and by the time I got to lawnmower blades, it started having some issues keeping up. I switched to my 220 outlet and BAM!!!... it cut like a hot plasma knife through butter. Overall, know the application you will be using it for and make sure you have a setup that can accommodate. As long as you have the right power and air for the job you are doing, I have not had any issues with this thing keeping up. If you have been thinking of playing with plasma cutting but are on a budget and don't want to worry about gases and stuff, this is a great option.

It just arrived today! So far, I'm impressed with it! I watched several youtube shoot out videos of the bestarc, arc captain, etc (basically cheap plasma cutters) and I decided to go with the bestarc BTC500DP 9GEN. I had an older (20 years) plasma cutter (also an off-brand model) and it had given up. I was looking for another cheap replacement. The packaging was great! Our Fed Ex delivery guy is not the most gentle when it comes to our packages, but this bestarc packaging was tight and very secure. Very easy to unbox and assemble! I had it put together and working in about 20 minutes. I have only tried it on 110V, but it cut some 3/16" very well and very quickly! I'm sure that once I hook it up to the 220V, I'll be able to cut 1/2" (or maybe more) with little issues. Very clean cuts! I bought the plasma cutter, a box of consumables, and a 3-year warranty for just under $210 bucks! If it last 3 years, it will be money well spent! If not, well that's what the warranty is for! If I used my plasma cutter for a business, I would likely invest in a name brand (Hypertherm). For my purposes and the amount of times I use a plasma cutter, I like the price and I'm impressed so far with the performance.

This is a great non-touch plasma torch. The design makes it easy to set up all cutting parameters. It’s lightweight, with all external connections done without tools. It’s equipped with an air dryer, which should extend the torch expendable parts life. All controls are on the front panel, easily set and read, except for on/off switch. It can be flipped on or off from the front, once you know it’s located. I’ve cut metal with for years but I’m a first time plasma user. I quickly cut various thickness and conditions of steel, and found it intuitive how to set up the pressure and current. There’s a chart with recommendations, but I found thinner metal below 3/8” could be cut cleanly and quickly with the same setting. All you need to do is cut at the best rate, and that’s learned quickly within the first inch of cutting. I did find it more difficult to punch a hole through thicker metal with plasma than Oxy-acetylene (3/8” and thicker), but the thinner metal was as easy as Oxy-acetylene. I’m sure when I developed the proper technique, the thicker gauge metal will punch easily. I felt so confident after 15 minutes of playing with my new torch, I started and finished two projects I’d been waiting to do because my acetylene bottle was empty. With plasma; all you need is an air compressor, and electricity. And this unit will work on 110 or 220, and both have a 50% duty cycle. For my two projects I was cutting with 220, and it cut both 7/16 and 16 gauge quickly and cleanly by only changing air pressure and current. With Oxy-acetylene I would have had to change tips and played with torch settings and pressures as well. Plasma is so much easier, with no expense of gas, and bulk of the torch and hoses. I’ll never go back! If anyone that reads this wants to buy an Oxy-acetylene system lock-stock-and barrel call me;-).

I bought this for my shop after watching a YouTube video review and reading reviews on Amazon, good looking unit and well packed but when I hooked air to it, the unit had a serious internal air leak that caused it not to hold a steady pressure which caused erratic cuts because it couldn't regulate the air pressure. With that said it did work, just not correctly. After this I called Amazon because it wouldn't give me the option to simply exchange it because there was not another available, so they had me contact the seller and it went downhill from there. The seller responded telling me to disassemble the unit and try to figure it out myself and then they would send me parts!!!! I told them I did not buy a brand new plasma cutter to repair it myself right out of the box and who was paying me to do (THEIR) warranty work? If I am working on the plasma cutter, I am not working on customer work which pays my bills and requested them to please just send me out a new unit and I could return that unit which would require them supplying me a return shipping label. They responded back asking me to please just take it apart (told me it was easier than I think) which is irrelevant to the situation and no option for a replacement, only that I could return it to Amazon for a refund. In-between those two exchanges I was mad and took it apart, found a bad airline quick connector and replaced it and also once that was fixed, I could hear the clear bowl leaking on the water Seperator, so I unscrewed it and sealed it properly which fixed the issues. Needless to say, I will never buy another product from this company no matter how well the product works after I repaired it. You simply do not buy brand new products to have issues right out of the box then have the company tell you to repair it yourself! In the end after I spent my own time to repair it and replaced a part myself on a brand-new piece of equipment, the plasma cutter does work very well. Customer service and QC obviously are both lacking. UPDATE: Since my original review they have contacted me several times basically harassing me wanting proof it ever had an issue in the first place and wanting proof I even contacted Amazon and was told they couldn't exchange it, only return it for a refund etc. basically calling me a liar at every point. I told them I was reporting them to Amazon and DO NOT contact me again, they didn't listen and still continued. This is what you can expect from this company if you need customer service. I own a business and I order many thousands of dollars a year from Amazon, have no reason to lie about anything and was only asking for a replacement unit and return this one, nothing more, nothing less. Because of my remark about who was going to pay me to do (their warranty work) they offered me a 20.00 refund and I told them to keep it because they evidently needed it more than I did, after I told them I was reporting them to Amazon they then refunded me 30.00 AFTER telling them I didn't want it. Sadly, if it was given out of doing the right thing in the first place, I would be singing them praises but it wasn't, it was only an attempt to cover their poor customer service AFTER the fact.

Works great. Had to open it up and reattach some airlines as they were a leaky but after that, it’s been working great since. If you have any issues with it, you probably just need to replace the consumable parts and it’ll fire right back up.

très surpris pour une petite machine a ce prix la découpe et propre et facile d utilisation

Bought the biggest one and it has performed very well as it has cut up to 3/4” inch with ease. Using it on a farm so not used everyday to test for durability but I’m impressed with the capability of the machine.

Es muy bueno considerando el costo del producto, hasta el momento eh cortado placas de 12 mm de espesor sin problema, logicamente a 220 v, es un buen producto, muy recomendable

الجهاز ممتاز ماشاء الله والبايع جدا متعاون ويرد عليك بسرعه من اول ما ترسل له انصح به

I like the air regulator in the front of the unit making it easy to see and adjust. The water drain and connection at the rear of the machine is nicely protected from being bumped. I like that you can adjust the time the air stays on after making a cut greatly reducing the wear on consumables. The performance is better then a lot of other machines at this price point with a 60% duty cycle at 50 amps 220v but at 35 amps it's 100% duty cycle (60% duty at 35 amps on 110 and 100% duty at 28 amps at 110volt just for info). Lastly when I unpacked the unit, I seen the torch tip was slightly black from them testing the unit prior to packaging. Definitely better quality control then other manufactures I've seen.