Thermal Grizzly TG Putty Basic - 30 Gram - Electrically Non-Conductive Thermal Interface Material for GPU Modding and Thermal Pad Replacement

Excellent Putty, used for an Xbox Series S improved performance and cooling form stock, paired with a fresh coat of Thermal Paste (MX6 Artic). Good value. I liked that it came with spatulas and gloves, it was a bit messy trying to not get it on everything was a challenge, easy enough to apply on where I needed it to go. Would defiantly buy again. improved the performance and temperatures of the Series S. Improved fan noise level due to better cooling from paste and putty. Fresh smells too which is always good for electronics.

Great value for price. Easy application and it works as intended. I replaced the putty of my laptop with this new one and together with replacing the thermal paste with PTM 7950, it helped cool down the temperature. It comes with a small spatula and this also helps. Overall, I recommend the brand and the product.

Thick and not to sticky drop temps better then pads.

Worked great on my waterblock for the 7900XT and reduced the VRAM temperatures from the stock pads. It makes measuring a lot easier, as it will just squash into place. The only problem is the price is a bit high.

I recently replaced the thermal pads on my GPU with Thermal Grizzly TG Putty (Basic), and I couldn’t be happier. It supports heights between 0.2 mm to 3 mm, so no more guesswork—just scoop, apply, and smooth. It comes with handy spatulas and plenty of material in the tub. 🔧 What I Love: Non-conductive & versatile — safe to apply on VRAM and VRM chips without worrying about shorts. Fills irregular gaps seamlessly, unlike thermal pads that can tear, compress unevenly, or age poorly. Noticeable thermal improvement — VRAM temperatures dropped significantly after switching to putty. ⚠️ A Few Caveats: Application takes patience — getting a clean, even layer isn’t hard, but does take care. Heatsink pressure matters — make sure there’s enough mounting pressure, or temps can rise instead of drop. 💰 Worth the Price? Yes. The Basic version is a solid value for most use cases. There are higher-end versions (Advance and Pro) with slightly better thermal performance, but for the price, Basic delivers excellent results. 📌 Final Verdict: If you’re confident working inside your GPU or laptop and want an upgrade over thermal pads, TG Putty is a fantastic choice. Just take your time applying and make sure the heatsink is properly secured.

Good product easy to spread and compresses well with cooler on top, temps are down for me definitely worth buying if replacing the thermal liquid on processor fills gaps easy

Used on my Inno3D iChill x4 RTX 3090 to rescue it. The card's VRAM was overheating causing bluescreen crashes. I took it apart, and found the rear plate pads were OK, but the front pads were dry and crumbling, so I liberally replaced all the front thermal pads with this TG Basic Putty, and repasted the GPU die with new thermal paste. There was not enough in the tub to replace the rear pads, but they were in good condition, so I spread the remainder as a thin layer to interface between the rear contact surfaces with the existing thermal pads on rear heat plate, to seal any micro cracks in those existing pads. The result has been that the card is now working perfectly again, and temperatures have dropped about 20 degrees C on the VRAM, and no more bluescreens or crashes.

I used this to replace the thermal putty inside a base PS5. Being almost 5 years old, the thermal putty inside (which looks like blu tac) had gone quite dry, crispy and flaky (see pic). I bought this because I planned on fully disassembling the console and thought it might be worth replacing said putty at the same time. I used the 'basic' version which is more than enough for the PS5. The tub it comes in was surprisingly small, but you don't need huge amounts. The benefit of using putty instead of pads is that you don't need to get the exact thickness. You can just make little blobs and when the components are rejoined, the putty will just squish to a suitable thickness. It's quite time consuming to apply, it's like a play dough consistency but not quite as sticky. You're not supposed to handle it with your hands because it impacts the effectiveness of the putty. I couldn't help it sometimes though.

4~5年くらい使ったRTX3070tiのGPUのカピカピグリスの塗り替えのついでに。 サーマルパットではあまり流通していないマイナーな厚さがあったため、ならばサーマルパテにしようと思い購入。 cpuにグリスを塗る感覚でメモリに塗ると全く足りないので、一度塗ってからヒートシンクをつけて外して両面に十分接着しているか確認するのをお勧めします。また、GPUホットスポット温度も合わせて確認すると安心だと思います。 サーマルパッドの時よりも多分冷えてると思うので、こっち使ったほうがいいですよ。とてもおすすめです。 内容量30gとありますが、私の場合は十分余ったので足りないことはないと思います。

This stuff works great! I only use thermal grizzly products now for paste and putty. Save the money and get this stuff over the two other premium tiers as this literally works fine as is! I used it on my RTX 3060 laptop as the old pads were literally dry and crispy lol! Dropped my VRM temps back to normal and was super easy to apply. It dissolves with ISO same as their thermal paste for easy cleanup:) Cheers

Tengo un xbox series x que suena como ventilador, se me apagaba cuando intentaba jugar ciertos juegos, aún suena pero ya no se apaga. Es un avance, si me sirvió. Lo único malo, venía con unos guantes y herramientas pequeñas, eso no es lo malo, lo malo es que la masa se quedaba pegada. Seguro se desperdicio algunos gramos.

Ottimo prodotto

Excellent product! Just fixed a broken gpu