Quick Clip Pro Holster Tough Grip Clips, 3 Hole Adjustable Cant for IWB OWB Kydex, Leather, Hybrid Holster Making. Tuckable Black Plastic w/Chicago Screw Hardware Made in USA

I used one of these clips to replace the worn out one on my Minimalist P365 - Mission First holster. It was a perfect fit and better than the original. I plan on buying more.

One year update: I carry my EDC every single day, 12 hours a day (at least). After a full year of using these clips on my Crossbreed Reckoning holster, they are still in perfect condition, and have never failed to retain the holster, after a dozen or so range trips and dry firing sessions. I also use them to retain numerous IWB fixed defensive knives, and again, 100% reliable! Only other retention solution worth using for IWB would be an authentic Pull-the-Dot snap on quality strap(s), buy those tend to take me quite a bit longer to confirm that they are propery secured on my belt. Bottom Line: Don't hesitate to get these for your IWB holster! I picked up a Crossbreed holster for a new Hellcat, but found their metal clips to be a bit weak on retention, and too high on the holster, resulting in the rear clip-top covering a critical index finger area of the pistol. These solved both problems. I'll be ordering a few more pairs for use on kydex knife sheaths to convert them for IWB use. These are a perfect fit on my 1.5" medium weight cobra belt, as well as my thicker 5-stitch instructor belt.

I like these little clips. Very sturdy. Pretty easy on and off. My one complaint is the hardware. It’s too short. The only thing I’ve tried to use them for so far is my cold steel Kobun Tanto. The sheath has slots in the side, and also eyelits which serve 2 purposes. They are the rivets that hold the sheath together, and also holes for mounting hardware. The hardware these comes with is long enough to go through the slots, but not long enough to go through the eyelits. I am able to just barely use these screws if I leave out the rubber washer, but not if I use it. Anyone who’s used this kind of hardware knows it’ll never stay without the rubber washer. Minor complaint. I have lots of longer TekLok screws lying around, so I don’t think it’ll be a problem.

I purchased these clips for a different use and work great! I use them to attached my “Molle Magazine Pouch” to the door in my safe. The “Quick Clip” slides easily right into the elastic straps on safe door. The cross straps on the Magazine pouch fits into the clip. These work as a great way to organize and when needed can unclip from safe wall. The “Quick Clip Pro Holster clips” was not designed for my intended use, however a perfect solution to how to attach or hang the pouch or any other items. See photo’s provided.

These are exactly what I've been looking for! If you have a kydex inside waistband holster with friction retention, drawing the pistol can often bring the holster with it. Sure, I could loosen the retention, but isn't that the point of having retention, so it doesn't just fall out of the holster? Regular spring steel metal clips just slide right off the belt. Regular polymer clips just slide right off the belt too. J-hooks seem like the perfect solution, except that the weight of the gun is on your pants, not the belt itself. These clip snugly under the bottom of the belt. I have a 1 1/2" bioshield belt (very firm and rigid belt), and it's difficult to remove the holster from the belt when changing pants. The only improvement I could request on this would be to be maybe 1/8" taller in the clip itself so that when pulling straight up, the bottom lip would still snag the belt and not release, but removing it from a belt intentionally could be a bit easier. Then again, I could have gotten the 1.75" clips and probably solved the same issue. The clips are thicker than spring steel, but have to be for strength. The price is a little high, IMHO, but competitive. You get two clips and hardware, but it's still a few screws, and two pieces of plastic. However, these are competitively priced.

Used these on a knife holster and they worked fine. Offer good retention and have a good design. Good clips for the price

I have been wanting to change the hooks on my Comp-Tac MTAC to 1) reduce the excess / unused clip below where it attached since I used the center hole on the MTAC clip and 2) make the clip more flush with the holster body since the original bumps the clip out with a thick rubber spacer. This presumably gives more room to tuck in a shirt, which I never do with this holster. Both of these create small bulge points in my pants below the holster. While not super noticeable, they have caused some wear and tear on some pairs of jeans. These clips seem to have alleviated the issue. Attached to the bottom hole, it’s about the same as the middle hole on the original Comp-Tac clip. The attachment makes the Comp-Tac fit closer to what I tried with a similar Stealth Gear holster (which I considered switching to for the aforementioned issue, but now is moot). I believe Comp-Tac formerly sold very similar, if not the same clips, on their website at one time, though they do not seem to have any accessories posted at the moment of this writing.

Really nice, sturdy polymer. Good reverse "J" clip that prevents holster from riding up off your gun belt. Has a slight lip that helps your finger lift the clip out from your belt for removal. Infinitely more secure that the metal OEM clips on my holsters. One time I was 20 feet up on a ladder, and one of those metal clips slid up and off my gun belt, and my 9mm fell to the floor below. Not only embarrassing but dangerous. They are also more discreet (no logo) and comfortable than metal.