Okinos Aqua 3, Micro ATX Case, MATX PC Case with 3 X 120mm 3-Pin ARGB Fan Pre-Installed, Panoramic View Tempered Glass Front & Side Panel, with Type C Port, White

Nice and compact case without too many compromises. Cable management is good, and it fits most normal sized GPU’s and CPU tower coolers. Very well built and rivals cases that are much more expensive

Oh my gosh, this computer case is absolutely ADORABLE!!! I LOVE it! It's actually roomy inside for everything I need. It's also very quiet and super clean looking. NO more big and bulky Cases for me. I have TONS of room on my desk now. Here are the before and after pictures. :) The Black case was before. This little White case is over half the size of my other one and I'm just absolutely Loving this. It's 15" Tall x 13" Wide x 8 1/2" deep. (from side to side in the front - 3rd picture) The Top has the metal mesh, and so do 3 sides towards the bottom so that enough air flow goes through, so your pc should not overheat. This is an Amazing PC case and at the very good price as well. :) If you are looking to go smaller on your Computer case, I would HIGHLY recommend this one. :)

Amazing little case, built with it multiple times in the past. If you're going to use an AIO, I recommend using low profile memory as clearance is an issue. I only managed to get the four front facing screws in while the backside of the AIO rested on the water pump. Might be an issue in the future but does give a sick angle of the fans. I used TL-M12Q fans in this case, highly recommend when trying to cable manage. Used old parts I had laying around besides the GPU, Fans, Cooler and case. CPU: Ryzen 5 7800X GPU: XFX Pro Gaming RX 9060 XT (Check for clearance prior to purchasing your GPU, maximum is 320mm) RAM: JUHOR 2x8GB @ 3200MHz Motherboard: B550M PRO SE Cooler: Thermalright Frozen Infinity 240 Dunno what else to say other than great case especially for the price.

This is a great-looking case. The see-through sides are the reason I got it. It looks great sitting on the desk with the RGB. The built-in fans are nice and quiet. All my parts fit great. Cable management was easy with the removable side plate. Very good value!

Great budget Micro ATX case for those starting their first pc build. The case comes with screws and zip ties and the connector's you plug into the MB. My only issue is the manual it comes with has no layout or label of what screws go where so it’s trial and error. There is sufficient space on the back panel for cable management even with the addition of PSU extension cables which I used. The ARGB hub the case comes with is basic but gets the job done! Works along side with your motherboards RGB controller software. I was able to plug in 4 fans as well as the ARGB on my cooler into the hub. It’s a pretty solid case. The space to work with is tight so I suggest you streamline your build so you don’t have to take a step back and remove parts just to have clearance to move connections or parts. As for thermals this case operates with a negative pressure system which is not bad. I found that you can fit slim 15mm case fans on the bottom of the case to increase air intake. Personally I did not like the fans the case comes with so I did end up switching them out. The fans were built a bit cheaply and ran loud. As for my build here are my specs for those looking for inspiration. CPU: Ryzen 5 5600x GPU: AMD XFX 6750xt RAM: T-Force DDR4 3600mhz SSD: Teamgroup MP44 1TB MB: ASRock B550m pro SE PSU: Corsair RM750 Fans: Lian Li Al120 Cpu Cooler: ID-Cooling Frozen A610

Bought this case after seeing a few reviews and like the size. Being able to remove the front glass to install the mobo and GPU was great. My 304mm would be a tight fit without doing it. To get the max claimed GPU length it is a must to remove it. I do have a couple complaints though. A few of the fan screws already had surface rust on them, which I was surprised to see. Took them off the back fan and put them on the top fans to be hidden by the magnetic dust cover. Functionality wise, it has been outlined in review videos. My mobo has the USB header on the bottom of the board. The cable routing holes are not lined up well and you end up having to bend the cable pretty sharply. I actually used a zip tie through the lower case fan mounting holes to keep it down so it wouldn't hit my GPU fans. I wish they would change the front USB ports to just 1 USB A and 1 USB C so you only need to use 1 USB header on the mobo. Since many of the smaller boards only have 1 USB 3.2 header on them and this is for a mATX or ITX board. There is an adapter that can be bought to go from the 19 pin USB 2 header to accept the USB C header cable from the case. I have not got one yet, reviews seem sketchy. Top rear case fan is tight with my CPU power cable. If the power cable was a single and not a double it would probably flex enough to not touch. I also wish the case had an included GPU support bracket like I have seem on some other cases. Things to keep in mind. Find a mobo with the PCIe slot at the max height. My Auros Elite AX has my GPU (XFX 6700XT) in the 2nd/3rd slots. There is no way to add fans on top of the case basement to help with more airflox being pulled into the case. I chose the mobo for the integrated wifi. Just research your needs and desired layout.

This is probably the best name for your buck case. It was easy to build in and looks so awesome with the seamless glass panels. My GPU is 322mm and fits perfectly so if you have something bigger unfortunately it's gonna be a no go for you. My main concern was the air flow and temps. I bought this when there was only two reviews so I was taking a shot at temps. While playing Fortnite my CPU gets up to 70 and my GPU gets to 53 degrees. These numbers are variable but it's still good temps if you ask me for bottom vent intake. It comes with three 120mm RGB fans which do a good job. Overall I'm so happy with my purchase as I believe this is the best value for your money. The aesthetics, air flow, ease of building made me give this 5 stars. I'd recommend this to anyone hands down.

I love this case. The white pairs well with all of my other white parts, especially my Yeston Sakura graphics card. I just upgraded to a Yeston Sakura 9070 after using their RX 6800 for years, and there was some legitimate worry for a few minutes that we would not be able to fit it in the case. The website lists its length at 342mm. Today we learned that the glass on the side of this case can be removed. Just apply a bit of pressure on the top of the glass and the little nubbins pop right out, so we could get this oversized graphics card inside the case just fine.

El gabinete es más pequeño de lo que uno se podría a imaginar ya que venía de un H6, midiendo este Oquinos 33.5 cm de largo x 39 de alto x 21 de ancho, la figura de una de las fotos mide 41 cm de alto y queda mas alta que el gabinete. Puede uno meter una gráfica que ocupe 2 slots de espacio de los 4 disponibles, si lo haces así podrás poner ventiladores en la parte de abajo que realmente te ayudarán a enfriar mejor el ensamble, ya que las partes malladas de abajo ayuda a qué los ventiladores de abajo de la gráfica respiren y den buen aire frio, así mismo el máximo de largo que pude medir con regla es de 32.5 cm de largo sin que golpe el vidrio lateral, podrias meter incluso una 4070ti súper de no se, AERO gigabyte que mide unos 30 cm de largo y tener un ensamble potente. Recomiendo ampliamente que pongan igual uno de los dos ventiladores de la parte de arriba metiendo y ya el segundo de arriba y el de atrás sacando aire. Mi ensamble es con una B650, un Ryzen 7600, una 4070, dos ram de 16gb cada, una fuente de poder de 750w plus gold y 5 ventiladores RGB duo de NZXT. Solo tiene dos detalles a considerar, el primero, que reemplaze los ventiladores de stock por qué realmente son la cosa más sencilla del mundo, no tienen controlador de velocidad así que siempre giran a las mismas revoluciones x minuto, si tienes la oportunidad de cambiarlos, hazlo, si no como quiera si te serviran en lo que le instalas algo mejor, y la segunda, es que en la parte donde se engancha la grafica al gabinete, los agujeros no tenian moldeado para tornillos, venia plano asi que tuve que poner un tornillo un poco mas grueso (de los que se usarían par sujetar alguna fuente de poder) para que pudiera apretar bien. Fuera de eses dos detalles, si lo que quieres es un gabinete pequeño para formato mini itx o micro atx y gráficas hasta 32 cm. Este gabinete es una opción muy bonita y se puede lograr un ensamble limpio y muy lindo.