Goupchn LCR Meter Test Leads Terminal Kelvin Clips Cable Wires to 4mm Safety Banana Plugs 1.2m/3.94ft for DMM

Excellent 4-wire, or Kelvin. test lead set, especially for the price. The leads are flexible. The Kelvin clips work well, they are made well, but relatively light duty. The banana plugs fit and hold well. The following images show 4-wire measurements using a Fluke 8520 meter with the clips shorted, measuring a 10 ohm standard resistor, and the clips on the 10 ohm resistor. Highly recommended. I just ordered a second set.

I bought these to use with a home-made milliohm-meter. The worked out perfectly. The leads are flexible, plenty long and the tension of the alligator clips is just right. They hold tight but are easy to open.

Decent gold plating on jaws and banana connectors, compliant but positive spring clamp action. I've had to add my own tags to indicate which jaw goes to which plug (sometimes it matters which jaw carries the current).

Good value for the money and they work just fine.

Good build quality, works perfectly, showed no tendency to fall apart. I used my (dumpster dived) Fluke bench meter to measure some suspect automotive fuses. The 5A fuses (ATM-LP in this case) should be 17 milliohms and they were. Fake Chinese fuses come out much lower, like maybe 1-2 milliohms. I can't measure that low with real accuracy.

I've seen a lot of test leads with Kelvin clips for more, but these seem to be the best. The pressure of each clip is consistent and firmly holds the device under test. The leads have a flexible and heavy duty insulation. If I had a concern, it would be the quality of soldering to the Kelvin clips. At first look, some of the soldered connections seem poorly accomplished, but the connection is solid. Be sure you insert the banana plugs firmly and completely into your meter. I was prepared to be disappointed when my 4-wire resistance measurements became flaky after a short while. I discovered that I had not fully inserted one plug into the meter. The plugs definitely fit firmly. I'm not saying that they are too tight, they simply have a firm fit which you want. These leads get a solid five stars for this review.

Well-built set of Kelvin clips. Gold coated alligator clips are well aligned and grippy yet small enough and unintrusive, banana plugs have overmolded strain reliefs, there are properly designed retention clips for the pair of cables along the way, not just heatshrink, and cables arrive properly on each side of the clip, not combined like in cheaper sets. All that for the same price as the lesser built ones. Now permanently attached to my HP 4262A LCR meter.

I bought these just to test the 4 wire resistance feature on a Keithley meter I was refurbishing, assuming I would buy/make a better set in the future. However, these exceeded all expectations and will meet my needs long term. Wires are good length and have supple silicone insulation - these are not stiff like some cheap probes. Banana jacks fit snugly. The alligator clip jaws align well. Repeatability of 4 wire measurements is within 4 milli Ohms - 20ppm for 200 Ohm full scale. I used a paint pen to mark the "force" side on the cable and the clip jaws to improve measurement repeatability.

低抵抗計メーカ純正の4線プローブが あまりにも高価なので、本品で代用。実測値は純正と変わりませんでした。心線も純正と同じぐらいの太さなで作りもしっかりしていました。

Very good quality for the price. May not be professional grade but works perfect for the occasional usage like we do. Works with our Siglent SDM3055 Digital Multimeter. Plug these in, short them together, REL on to cancel the ohms of these probes and you are ready to test low ohms. At these prices you can buy a few of these if you use them often and still come out ahead compared to more expensive units. I would purchase again. Very flexible cabling. Five stars for price to performance ratio. Pictures show meter and measurement of 0.1ohm rated resistor.

Works great with my Fluke 8840a. This is a must to have with a compatible DMM.

Very good quality and very soft to the touch.