SPACEKEEPER Workbench Casters kit 920 Lbs Retractable Casters Heavy Duty Bench Caster Wheels Side Mounted Retractable Workbench Wheels Designed for Workbenches Machinery & Tables, 4 Pack

When I got it, I ran a test by mounting it on a 2x4, it worked fine. Three weeks later after I built the 2'x4' woodbench, I installed all four legs. It works very well, solid and easy to operate it. But, two comments about this product: - The installation manual is a joke, useless in one piece of paper with simple drawing. Look their product pictures, that's more detail of how to do installation. -2nd, the template is1/8" off, too short, don't follow it. Use the real plate will get the job done right.

They work pretty good, I have a large work table and these do the trick for moving it around.

Fully supports my workbench. Easy to install with the provided template. My only criticism is that the supplied screws are prone to snap during installation. After the second one snapped, I switched to my own, higher strength screws. I would buy another set for my next mobile work project.

Very well made, some of the normal casters don’t hold up very well these are a little more complex with the retractable function and I’ve got them installed on a 350 pound 4’-6” X 10’ woodworking table they roll perfect and turn excellent it can be pushed with one finger.

These wheels work great and are easy to install.

I tried to use the wheels to occasionally move around a tire machine. No problem with the installation. Used my own nuts and bolts, and drilled directly into the steel of the machine. Pushed the levers to raise each wheel, everything ok. Then I rotate the machine, everything ok, until I bumped the the side of a carpet runner on my concrete floor. PROBLEM. 3 of 4 wheel studs bent. POOR design, all the weight of a wheel is on the single hex part of the wheel stud. That might be 5/8"? Wheel metal must be made of very soft steel, Chinesium, probably. My wheels bent , yours might , too. That's when I found some used all steel wheels where the weight would be distributed over a much greater area, at least a 2" radius, each. So I spent about $40 to use the bracket/lever part, Junked the rest, and added my own wheels. Now , No problem. So Be aware that the poor design of the small stud area can't possible be rated for the 920 pound weight of a set of wheels. Unless you never bump into anything. If you're trying to move around something much lighter, it's probably fine. 920 pound rating , for the whole set, is B.S.

Great, sturdy coasters, easily to lock and unlock . Smooth swivel. Easy installation with necessary screws, bolts and ranges included in each kit.

I installed these on a bandsaw that weighs about 800lbs and they are not handling the load well. They have started to bend, and they no longer stand up straight when I lock them in the down position. I am now looking for alternatives. It's a shame I had to drill this many holes to find out that they don't work.

Me gusto el producto.

Works perfectly. Heavy duty materials, can lift a lot of weight. However the instructions are somewhat contradictory and images unclear. First construct the bracket (silver piece should have ridges up), as in my photograph. Then cut a 2.4" high piece of wood and clamp it to the base of the leg. Install the bracket above that piece of wood. Only then attach the wheel to the bracket. Also, as others note, the orange/red step end falls off because the manufacturers used the wrong kind of glue (it has to attach plastic to metal). I re-glued with a two-part epoxy glue, then clamped it on for a couple of hours and now it's on solid.

Attached this to a welding table and it works as expected but would prefer a version with metal wheels for use in a welding shop where small pieces of sharp metal end up on the floor to dig into the plastic wheels. The red plastic caps comes off the first time you use your foot to crank down and raise the table.

Herrajes 7 de 10 Llantas 10 de 10 Gomas 3 de 10 ( las tuve que pegar con silicona) Tornillos 3 de 10 (se nota que son de baja calidad) Pijas 1 de 10 (se barren al momento de instalar, utilice otras pijas de mejor calidad) En resumen, compren de otra marca.