🚦 Stop the Blink Panic: Fix LED Signal Errors Like a Pro!
The Safego 50W 6 Ohm LED Load Resistor is a high-performance electrical component designed to prevent hyper flashing and error codes caused by LED turn signal and license plate lights. Compatible with a wide range of vehicles, it simulates the load of a traditional filament bulb to ensure smooth, error-free signaling. Easy to install with included wire clips, its durable aluminum construction safely dissipates heat, making it an essential upgrade for modern LED lighting systems.
| ASIN | B06ZYCTF5Q |
| Auto Part Position | Inner |
| Best Sellers Rank | 265,302 in Automotive ( See Top 100 in Automotive ) 644 in Motorbike Indicators |
| Brand | Safego |
| Brand Name | Safego |
| Colour | 50W 6OHM |
| Customer Reviews | 4.2 out of 5 stars 1,005 Reviews |
| Item Weight | 2.11 Ounces |
| Item package quantity | 2 |
| Light Source Type | LED |
| Light source type | LED |
| Manufacturer | Safego |
| Manufacturer Part Number | SGDZ50W60OHX2 |
| Package Quantity | 2 |
| Specific Uses For Product | Rear Lights |
| Specific uses for product | Rear Lights |
| Voltage | 12 Volts |
| Wattage | 50.00 |
B**P
Finally error message gone
I tried 2 different makes of Canbus error free T15 (921) LED bulbs, both of which give an error lights out message on the dash in my standard 2012 Audi TT 1.8 TFSi coupe. Its only the reverse lights i want to be brighter. After fitting these resistors the error messages have finally stopped. I have left the car in reverse for 2 mins to test the heat of the resistors, they only got slightly warm, so absolutely fine for reversing light application.
R**.
Works perfectly.
bought the 50w 6 ohm load resistors due to fitting LED units and having "hyper flash" when indicating. Fitted this kit in around 15 minutes. very easy to fit and works perfect. does get slightly hot when the indicators are on for a prolonged period of time so something to bear in mind when sticking the resistor down (i.e. not near to plastic or fabric). A little bit of double sided tape on the bottom would be a good addition. However I had some lying about just to stop it moving. Quick splice connectors are included. A set of pliers or pump pliers are needed to fully close the metal blade.
U**�
Four Stars
A1
J**S
Worked for Audi a3 LED headlight conversion
Worked in my Audi a3 I had LED lights but the car thought the bulbs was blown. Wired these up nice and easy about 20 mins now car no longer has error and has no affect on the way the lights work. Will be ordering more for my full beams now
J**N
Work great, but get hot
Work as expected but do get very hot, however for about 6 month I wired them in wrong, you have to remember to wire them across the positive and negitive connecting the two, seemed counter intuitive to me but now they work great. I used them on a John Deere 6170R to allow LED flashing beacons, without a canbus fault showing.
D**E
Resistor
Perfect item
A**R
Poorly made - does not spread out it's internal heat
I tried to use this resistor as ballast for LED turn bulbs. In use, one end in particular got really hot to the point that the lead to the component melted the solder joint. This was at half-on, half off. I'd definitely not recommend these.
L**N
great
works great as others say mount on metal as god they get hot
G**Y
does the job.
definatly remove hiper flash. wires are wrapped in a fabric braid style. made it kind of hard to strip. wires are definatly long enough to support a permanent mount. holes for mounting are very close to the body making it quite dificult to use a standard sized self tapping screw to mount. all in all great product. does not get very hot but recommend mounting to a flat metal surface.
B**E
Mute bueno
Gostei.
R**N
Worked as expected.
Easy to install
一**人
値段の安い物でも当たり前に機能する。
普通に機能しているので特にありません。
M**R
Led widerstand für blinker
Die Erwartungen wurden voll u ganz erfüllt! Funktioniert einwandfrei u wurde rasch geliefert. Werde wieder bestellen wen ich etwas benötige! MfG
Trustpilot
2 months ago
2 weeks ago