3D LAC 80ml Adhesive Stick for 3D Printing

Great bed glue for asa👍🏻 never had any issues.

Bambu P1s. I normally print strictly PLA. Never printed anything else. Needed some UV stable material, found out about ASA. Printed a couple of things and had decent success on small things but large or long things bed adhesion was very hit and miss. And yes. I clean my plate. Washing up liquide. Hot water. Quick wipe with IPA. Even with brims. Still struggled. A friend recommended this. I still follow my cleaning ritual but my God this stuff works so well. Apply in the area to print. Allow to dry ( the bed drys is at 100c for ASA) but this stuff pretty much has taken 99.9% of any anxiety about printing ASA. Do not use Brims with this. I had an absolute nightmare getting them off. Well worth the money. Amazing stuff.....

This works as expected and does the job, but I’m a bit on the fence about it. I prefer the spray version, as the dabber-style application isn’t my favourite and feels a bit less consistent. Adhesion itself is fine once it’s on, but getting it applied evenly takes more effort than it should. Nothing wrong with the product as such - I’m just not convinced the dabber format is the best way to apply it. I’d probably stick with the spray next time.

We have a FlashForge ADX5 3d printer and purchased this when our FlashForge adhesive ran out. At first we weren’t impressed as nothing we made wanted to stick to the plate however then my son experimented and realised that if you pre heat the bed to 40 degrees before adding the adhesive it worked great. No odor that we have found, easy to use. Would purchase again now we know to pre heat the plate.

Anyone using glue sticks should take a look at the price by weight and compare it to this. With glue stick I found it impossible to get an even layer on the plate and removing it effectively from a textured build plate was a long process. This stuff is considerably cheaper than glue stick by weight and is made to give you an even coating. I haven't printed many models with it yet but what I have done has shown me improved performance over glue stick and is very easy to wash off. One use has so far given me four prints without needing to wash off and re-coat which is again, better than glue stick.

When it comes to ensuring proper bed adhesion across your entire build plate, the 3DLAC solution is one of the best options available. However, while the 3DLAC aerosol and spray versions perform exceptionally well, the 3DLAC Stick falls short. Unfortunately, the stick delivery system introduces several challenges that impact the consistency and overall user experience. ### Functionality: The 3DLAC Stick mimics the older methods of applying glue sticks for adhesion, but this approach has inherent flaws. Despite its convenience in theory, the execution is clumsy, resulting in uneven application. This inconsistency can lead to frustrating printing experiences, particularly when trying to achieve a smooth, even coat across the entire build plate. The main issue lies in the stick's inability to deliver a uniform layer of adhesive. Since the glue is translucent, it’s difficult to gauge where the product has been applied, leading to high spots, low spots, and missed areas. While the places where the adhesive is correctly applied adhere well and release easily upon cooldown, the inconsistency means that other areas may experience poor adhesion or leave unsightly residue on your print. In addition, after a few uses, the stick becomes messy, with dried adhesive building up on the applicator. This residue can flake off onto the build plate during future applications, which can cause further defects in prints. ### Pros: 1. **Excellent bed adhesion** with the 3DLAC solution when applied correctly. 2. **Fairly easy to use** compared to some other methods. 3. **Competitively priced** compared to alternatives like Magigoo. 4. **Low odor** during and after application. ### Cons: 1. **Inconsistent adhesive layer**, leading to poor adhesion in some areas. 2. **Marks and defects on prints** due to uneven glue application. 3. **Messy over time**, as dried adhesive builds up on the applicator and flakes off. 4. **Dried residue can ruin prints**, if unnoticed during the application process. 5. **Takes significantly longer to apply**, compared to spray versions. ### Conclusion: In summary, while the 3DLAC Stick can provide good bed adhesion in certain areas, the inconsistency of the application makes it a less effective option compared to the aerosol and spray versions. The stick is slower to apply and prone to messiness over time, which can lead to print defects. If you’re looking for the best solution for smooth, flawless adhesion, I highly recommend opting for the 3DLAC Aerosol Can or Spray. These delivery systems are faster, more consistent, and ultimately provide a far superior result.

Did nothing, gave in and used a pritt stick instead an had much better success

couldnt ask for anything better, had tried to make printer goop previously but had issues with it acting as a repellent. likely my own fault. its based on similar active ingredients (PVP/PVOH). This stuff WELDs my ABS prints to the print to my PEI build plate only releasing when cold, the residue can be removed with water once released. printed a large ABS model with no brim with this and had 0 warping, curling, flat to the bed until it finished.

This spray is absolutely effective, almost too effective lol I've applied it to a bambu P1S, H2S,and H2C. Also applied it to an elegoo CC1 and boy nothing comes off anymore, even sometimes when I'm wanting it to lol. It's super easy to use, just spray and let dry and you're in business. Plus the value is good because a little goes a long way. If you have adhesion issues if any sort give this a shot, you won't be sorry

Werkt perfect.

Niezastąpiony klej do druku. Ja korzystam z niego do perg carb bo tak przywierał że rozwalał płytę albo wydruk. Z klejem po problemie

Works perfectly, I have been using the spray for years on glass, PEI smooth and textured, never fail me, even printet ABS without enclosure, just jumps off the bed below 40°C. Now I bought this stick and I must say that it works as good as the spray but with no mess from over spaying that could happen with the spray when I did it on the printer. Just have to remember to shake it well before applying.

This is excellent. I used to use hairspray or pritt-stick and this is so much better