STORMGUARD 02SR0200914W Bottom of The Door Brush Seal Draught Excluder, White, 914mm

Used on all doors works well

Fantastic quality for the price. Draft excluder. White metal top, with silver screws and a black excluder layer. This is 6cm long, the excluder area is 3cm long, so it can cover a good length. All the installation points and screws are set and provided. This was fairly easy to cut neatly. This is nice and durable, it didn't bend or scratch when cutting. The inner bar did slide out a few times after it had been attached to the door, so I added some glue on the end to stop it. This does work brilliantly for keeping the drafts out, I've placed one either side of the door. This looks nice, works well and it closed the gap I had! I would recommend this, for this price it is fantastic. It's good quality and looks decent enough too.

Arrived quickly, well made and ideal length to fit most doorways. With some careful cutting down to exact size this was installed on my sons bedroom door in just a few minutes. Simply screws on the the lower edge of the door. Make sure you check the pre-drilled holes and which side/edge you are cutting down BEFORE cutting. ++ For the neatest finish, if you're a bit of a perfectionist, here's my tip; If the door is LEFT HINGED then cut the surplus off the left side of the draught strip so the end you've cut is nearest the hinge (and the end you've cut is therefor less visible). If the door is RIGHT HINGED then cut the surplus off the right side of the draught strip, again because the cut edge is then less visible. And don't cut through the screw hole if you can help it so the strip is attached at fairly regular points all the way across and not flapping loose at one end. All common sense but thought I'd mention it!

Easy cut and to install. Perfect for white door I have one on the understairs door as there is an outside window which lets cold air in and there was a draft but there isn’t now.

OK item, but it lost two stars because it arrived bent at one end. I did consider sending it back, but worked out that, if I cut the excess from the faulty end, then I would still have enough to work with. Also, when you cut it, the black brush pieces tend to fall out of the end. You can't pinch it together, because it's plastic, so I ended up gluing the end brushes in place before fitting it.

This product works really well to stop any draughts coming under the door. They are easy to fit and very robust. I fitted them to both exterior doors many years ago and they still work really well. I can really recommend these draught excluders.

I bought this draught excluder to cover the gap at the bottom of my bathroom door, and it has worked perfectly. No more cold drafts! When cutting to length it is advisable to use a hacksaw, as the bristles are enclosed in a metal strip. Once cut I crimped the cut end in a vice and then added a spot of superglue at both ends of the metal strip to ensure no bristles came loose. After 3 weeks not a single bristle has come out. Cutting the plastic backing to length will likely result in the supplied drill holes no longer being evenly distributed, so I drilled a few extra. The supplied 4 screws are not enough, so I added two of my own, which are needed to ensure the, rather flimsy, backing is tightly fixed to the door at both ends and along the entire length. All these modifications are simple and easy to perform and I would thoroughly recommend this product. A 10 minute install has made a noticeable difference to the warmth of my lounge, off which the bathroom lies.

We have a bit of a draughty house so I bought a set of these to go on our front / back and living room doors. I'm pleased to report that they have worked exactly as intended and we no longer feel a draught. We have a baby and she has a play mat on the floor in the lounge but we were conscious of their being a draught coming into the room at floor level from the door but these have completely put a stop to that. I think it has also helped to retain some heat in the room as well. It was really easy to install using the self tapping screws, just offer up the excluder to the bottom of the door making sure the bristles are touching the floor and screw into the door. It couldn't be easier. I even had to cut one down to the right size for the door and I was able to use a regular pair of wire cutters to just snip it off (some strong scissors also work)

FA IL SUO LAVORO E BENE.

Ist ok

comprati per adattarli alle ante scorrevoli dell'armadio a muro. sono semplici da installare e modificare. anche se scorrono tra destra e sinistra fanno il loro lavoro egregiamente. L'installazione è con viti appositamente fornite, ma grazie al supporto in plastica ampio si prestano anche all'incollaggio. forse un po costose.

Hab erst nach 4 Wochen die Packung geöffnet darin befand sich die falsche Leiste in der falschen Farbe und zu kurz. Bin echt sauer😡

Ho una porta un po' datata e quindi nella fessura in basso si vede la luce ed entrano molti spifferi soprattutto in inverno. Grazie a questo prodotto non sento più entrare freddo dalla porta ed è un buon segno per me! L'installazione è facile ed intuitiva. Davvero un ottimo prodotto!