Araldite ARA-400012 Instant Syringe Epoxy, 24 ml, Packaging May Vary

Excellent glue, but the 'INSTANT' version 'goes off' extremely quickly, so this is only good for very fast, small, spot glue jobs. If you need to mix a lot for sticking large areas and things together, buy the regular Araldite.

Sets quickly. But didn’t seem to set as hard as the 5 minute version. It may be down to user error. Or not allowing to full set before putting strain on the glued joint.

This is the best adhesive, bar none. There really is nothing that comes anywhere close to it. I’ve been using it since the 80’s and I’ve not found anything anywhere near as good. I use it mainly to glue 3D printed parts and the glue joint is usually the strongest part. It’s super convenient to use with the dual syringe setup, just squeeze, mix and apply. After 10 minutes or so there’s no turning back - the joint is permanent. Overall I can’t say enough good about this glue. There really isn’t anything that can compete with it.

don't bother with the mixing nozzles. just put what you need on a piece of card and mix in little amounts. sets quick and does a great job.

This glue is really strong when mixed. The problem is that, unlike the 'old days', when you'd squeeze a bit from two tubes and mix them together to make it set, now it comes with a nozzle which mixes the two parts for you. "Great, that's easy", you say - and, yes it is, but the problem is that you can't clean the nozzle out, so the glue sets in the nozzle, so the nozzle is not reusable. It does come with two nozzles, but given that I just used about 1ml of glue the first time (that's all that was needed), and I estimate about 3ml was left in the nozzle, that's only 4ml of the 24ml used. If I use a similar amount next time, I'll end up throwing half of it away because I have no way of using it as the nozzles have been used up. Note that what I received is not like the image for the item, which still has the old 'mix it yourself' system, which was much more economical. In these days of trying to reduce waste, it looks as if Araldite has taken a huge step backwards by changing to one-use nozzles and a system which means you'll waste most of the glue as well.

Didn't like the mixing nozzle - it needed excessive force to squeeze the product through. But it worked fine without it, mixing in the conventional way. Therefore does not warrant knocking a star off.

Eventually got some to come out of the nozzle. Boy, you need strong hands to get it going; then it dribbles out. Use it on an old piece of cardboard to save messing up worktop. The nozzles can only be used once, and as it cures very quickly, if you have more than one job to do you'll need to line them up in a production line before the nozzle dries up. The little plug that you put in the tube assembly to blank it off will have a blob of dried glue in it so you can't get that back on. Fine for the couple of broken things I had to repair but the rest of it will probably thrown away, and it's hardly cheap to buy. And £10+ for a pack of new nozzles is a bit of a rip off. Will find a different make in future and buy one that you mix yourself like in the old days Yes, an innovative idea but impractical to use.

Excellent fast cure clear epoxy, only gripe would be that the 2 tubes provided generally mean only 2 uses which is not so good for smaller jobs where the tube maybe used many times.

il prodotto ha ripsettato pienamente le aspettative. la consegna, come al solito, è stata più veloce di quanto scritto nella mail di conferma. Prodotto consigliato

This syringe version is OK the first time it is used but the miixing nozzle is then full of hardened araldite and trying to extract the glue and hardener afterwards is difficult. Better to have two separate tubes which is what I'll buy next time.

I used this on glass, worked great. Won’t know if it turns yellow for a while.

La porte miroir d'une armoire de salle de bain s'est détachée. Après examen il semble qu'un pièce métallique s'est décollée et est restés clipsée sur la charnière. Après mainte recherche sur Amazone pour trouver un produit livrable en Belgique - une possibilité de recherche incluant ce critère serait la bienvenue - je reçois ma colle en question. Le mode d'emploi est assez simple et la double seringue permet un dosage précis. Après ponçage et nettoyage des 2 partie métallique, une est restée sur le miroir, j'encolle les 2 face après avoir mesuré soigneusement l'emplacement de la pièce à refixer. La pris rapide permet quand même d'ajuster pendant quelques dizaine de seconde. Ensuite utilisation d'un serre-joint pour laisser la colle se figer pendant une nuit. Il semblre que la colle soit efficace. Rplacement aisé de la porte miroire sur les 2 chanières, j'espères simplement que la fixation durera dans le temps. Les tubes sont fourni avec un double bouchon, j'espère qu'il empêchera les seringues de se boucher. A priori super produit et pas si cher compte tenu des services rendus.

Todo correcto. Llegó bien. Funciona.