Microphone Shock Mount - Isolation Mount Compatible w/ Blue Yeti Microphone, Yeti Pro, Snowball and Rode Mic Arm - 5.5 x 3.5 Inch Isolation Shield Silver

Works great and attaches perfectly to the Blue Yeti mic, I did have trouble trying to install it on the mount as it didn't fit but I then realised there was a plastic thread attached to the screw insert that you actually need to unscrew off. Once that came off, it fits on perfectly as you can see in the photos. Also I recommend you use a strong mounting arm such as the Rode PSA1 (which I purchased and is available on Amazon) otherwise the mic head will keep dipping due to the weight of the mount and mic. This is also less than half the price of the official Blue Yeti mount and is definitely worth it!

Contrary to the adverse comments made by some unlucky folk I can report that I received delivery this morning and have been delighted to find that the aluminium shock mount is almost perfect. Everything fits and although I have the Yeti Blue Pro Edition with the additional XLR socket in the base, there is still plenty of room for this plug along with the mini USB plug and mini headphone jack. My only slightly adverse comment is that it seems that you are able to have the mic on top of the mount as well as hanging underneath but when used with a gallows arm the tightening screw for angle adjustment is very prone to loosening as mentioned by other reviewers but I think that there is room for an additional anti slip washer to cope with this. All in all, a good buy!

This is a good alternative to the Blue RADIUS II. It's very stable and nice looking/feeling and it does its job. The only reason this isn't a 5/5 is the tinkering required. My microphone wouldn't fit on without removing the padding at the bottom; I didn't want to scratch my microphone and just leaving it hanging forwards. So I made my own alternative, it only took 30 or so minutes so not that long, however, a bit inconvenient. Overall very good quality and would recommend for the Blue Yeti especially with its competitive pricing.

Excellent shock mount, it is very sturdy, and it holds the weight of a blue yeti fine. I have noticed a distinct reduction in desk noise, key pressing / etc since installing this. Important note: There appears to be a batch of blue yeti microphones where the screw hole is 1/16" larger than the standard 5/8" it is supposed to be. This of course makes it impossible to screw any standard shock mount into the microphone. So if your shock mount doesn't fit, it is not Auphonix's fault, it is a microphone manufacture error. That being said Auphonix have said this on the matter: "IF YOU FIND YOUR MOUNT DOES NOT FIT - We will REFUND you, but there is an easy potential solution you might want to try first If you have a shock mount that does not fit, the problem can be simply fixed by using 'plumbers tape' or 'thread tape' around the screw on the shock mount. This very thin tape is designed to properly seal water pipes, but it will also help in this situation. Just wind the tape on 7 or 8 times to thicken up the screw, and it should fit nicely into your Yeti. If you would rather have a refund, please let us know immediately. Even though the fault is with the microphone, you've now got a shock mount that does not fit. We are very happy to refund you for your purchase in this case."

This mic mount isn't easily adjustable. Even when tightened as much as possible, the mount clicks out of place, so of course my mic does.

Very good shock mount, eliminates a lot of noise, and got it working very well with rode psa arm. It fits my yeti perfectly, the only thing I would say would improve this is to have teeth on the hinge, but that's based on the official shockmount and mine hasn't actually moved down yet anyway, it was more of an observation. All in all though, does what I wanted to do so I'm very happy.

First off: I immediately receive an email from the manufacturer, making sure i knew that the Yeti had 2 different thread gauges,and how to modify the mount when it arrived to fit the alternate gauge if that was an issue. Luckily i didn't have need for that advice as it fit on. I had real issues with fan hum through my desk, and that was resolved immediately with the mount. Keystroke sounds were lessened and i was able to record voice without any distortion or other factors. It means i didn't have to spend an age in noise reduction in my Sound editor, and made the Yeti the best microphone it could be. And at a price point that was reasonable. Heartily recommended.

Looks good and works well...but. The yeti is not light and so even when the hinge is fully tighted, it will hold it up until a butterfly lands on it, or you touch it to change the volumn etc. and then it droops. A minor niggle hence the 4 stars.

See thr size of auphonix as compared to blues radius shockmount. It is way smaller and broke easily.

Don't mind the incomplete studio, in the process of setting stuff up. lol I've been searching for an alternative to Blue's suggested Series 2 shock mount for my Blueberry for a while. The bands and positional arm on Blue's product are just terrible for what its going for so when I found this Auphonix shock mount it looked like a promising alternative at an unbeatable price. That said I understand that this is not made for the mic that I have. So here's my take on the product. Pros: 1) Obviously the price point. Way cheaper than Blue's Series 2 shock mount and other alternatives. 2) It worked on my Blueberry mic, though not without modification which I'll get to later. 3) Feels very sturdy after modification. 4) Looks great. 5) The company goes a great distance to educate customers about the manufacturing fault on Blue's end. Cons 1) The screw that is used to attach to the mic did fasten to the mic well, but it didn't fasten to the shock mount itself leaving room for the mic to shift up and down. I found a really cheap fix which was to get a 5/8" grommet which I sliced down the middle which helped tighten it down to the shock mount. 2) Not sure if this is Auphonix's issue or Innogear's issue, but the arm would not screw down as far as I would like it to on my boom. Though it is fastened down tight enough, I'm not quite 100% confident it will last for long. Any tighter I'm affraid I may strip the threads, but it is on and not moving around. As you can see there's definitely some room for improvement such as maybe providing a washer or grommet along in the package and maybe rework the thread to be able to attach to innogears larger boom. For now I got it to work, but I'm pretty sure others won't be happy to have to modify something they just bought. Modifications aside, for the price this isn't too bad. I say give it a shot. You might get better results than I did if you are using it on a yeti. ***** Update: I've been going back and forth with the company talking about the modification I had to make and the issue with fastening the shock mount to my boom. Long story short they sent me another shock mount free of charge and this one was able to screw down perfectly onto my boom. Now I still had to use my modification (grommet) to screw down to my mic, but I actually prefer it because it not only helps fasten down the mic to the shock mount, but also helps keep you from screwing down too much, and helps prevent scratching the top with the screw if you are able to get down that far. This company has been a real pleasure to work with and from that alone I would buy from them again. I highly recommend buying this if you are looking for a solid, yet cheap alternative shock mount to replace the Series 2 by Blue for your Blueberry. Get it.

Ottimo prodotto, ben costruito, perfettamente compatibile con Blue Yeti (buco-gate permettendo). Il lavoro di assorbire e dissipare eventuali vibrazioni prima che queste vengano registrate dal microfono è svolto egregiamente. La qualità dei materiali è buona, consona col prezzo pagato in un ambiente "onesto".

Works perfectly with my Blue Yeti, has eliminated all unwanted noises and delivery was perfect! Very happy!

Does the job as advertised