ElecGear 8X ALPS 10K Replacement Potentiometer + Drift Fix PCB for PS4, Xbox, Elite, Switch Pro Wireless Controllers, Trim Pot Resistor Thumbstick Module Sensor for ALPS Analog Joystick

Replaced just the inside sensor from this at first. Didn't work. Soldered in two for two different controllers and both work great so far. Might update if they fail soon. Walmart xbox one x controllers.

These potentiometers fixed the drift and range of motion issues my Elite Series 2 controller developed after several years of use. Installation is not the easiest if you are new to soldering, but it is possible to do with soldering iron and solder wick.

I replaced my left joystick up/down and so far the controller works great again. I replaced the entire unit, desoldering took a little bit but wasn’t bad. Soldered right together. Now I can fix all my other controllers too lol

I brought 2 old controllers back to life and still have 8 of these things left. Works as described, so far so good.

I tried the no-solder method and found that simply gently removing the sensor caps and removing the old sensors was an annoyance compounded when one of the caps snapped. The plastics used in the Xbox One controller are so thin and brittle that the margin between removal and breakage using a nylon tool is paper-thin. I am not going to invest the time in replacing the whole sensor assembly and soldering the new one to the PCB. If you're hoping for a similar easy fix, be warned.

Remember to recalibrate with the xbox accessories app when done.

I don't normally leave reviews, but this is my 2nd time purchasing these 10k potentiometers from ElecGear. The first set I got was to replace on Dualsense and Xbox controllers. About half of these are junk. Measuring with a multimeter, you will get a variance value of anywhere between 8.9kohms to 9.5komhs. While that value is normal, its not until you install these on a controller that you notice a lot of noise and resistance spikes. My second kit, I tried all of these on a Dualshock Thumbstick with and without 1.8v applied and when pressed in the directions, resistance is all over the place. ± 150-200kohms. Not a single pot in this kit went back to the the values it should be. Pressing on the left axis, Not a single pot went close to 0v. The best I could i get was 0.5-0.9. Pressing on the right axis, Not single one of these pots made it within 1.8v. The best pot only reached 1.53v when the right axis was pressed in all the way. I'm actually starting to think these are not real alps potentiometers. Ive never had so much issue with pots in my life. Aside from all of the horrible values, the noise on these is really bad. Noise that causes resistance value changes at rest between 150-220kohms. I will never be buying these again. Spend a little more and get some better pots.

i play genshin impact on PC with my SN30 pro+ and for the last month ive been having issues with my controller. my character sometimes takes random steps. and in the shortcut wheel the corner options are hard to hit (for example upper left and lower right) now that i changed them out, i can reliably select the battle pass on the shortcut wheel and yanfei can finally stand still. i didnt even need to use the included resistors. i still have 4 Potentiometers left and all 10 resistors left now i can reliably finish my battle pass and send hoyolab more money when i can. tl;DR; the 10k Potentiometer worked reliably in my 8bitdo sn30 pro+.

Perfect replacement and the included adjustment pcb was a very welcome addition but not needed in my case. The one I replaced was dead accurate immediately after installation per the Xbox calibration screen

Worked perfectly on my Elite series 2 i just changed the internal component and now i have no stick drift problems

They have bad characteristics. Wanted to get rid of my stick drift on Xbox. Had to go through 4 of them. After replacing the first, second and third the stick was working but it was very fast horizontally on original box resistor and very slowly responding vertically on those ones. Doesn't recommend.

Buen producto

Horiのスティックがドリフトするようになってしまったので購入しました。 Horiとプロコンは同じ部品だと思って謝ってグリーンの方を買ってしまったのですが、 3か所のでっぱりをニッパーで切れば、なんとか付けることが出来ました。 いくつか不良品があるのを覚悟はしていたのですが、運が良かったのか、1つ目の交換で正常に動作しました。