Rhino Rack M626 Vortex Generating Strip

Used these on my cx-50 crossbars. Really made a difference. Was skeptical at first. Just may want to glue them in though, lost one at 75mph on the interstate once after it pulled out of the crossbar

Ordered these because of a loud, high-pitched, whistling noise that I couldn’t get to go away on my Tesla model Y. These immediately fixed the problem. Would highly recommend!

Too expensive for one strip of rubber, should be at least 3 to fill rack bar!

Just bought an aftermarket roof rack off Amazon for my Model Y. Works great except for the whistling around 50 mph. Seems to be a problem even with the rack Tesla sells. Bought 3 of these strips and slightly cut the third one to fit my rack. The whistling is now gone even at 65 mph. Don’t mind the lower ratings for this product…most of them complain that it’s too small but they are the size advertised. You will probably need at least 3 side by side for your rack. Very impressive product especially for the price.

So I purchased this because I bought a rhino rack for 100 bucks on offerup. I know sick deal right? Unfortunately it didn't come with the vortex strips so I kept hearing a loud whisling noise staring at 30 mph. I learned about these strips and instead of wrapping my racks with a bungee cord or putting aluminum foil tape on the top to cover the gaps, I decided to go the more expensive and sexy route which was just to get these damn things. First off, my rack is 43 inches long, these are 15 inches each. so you can see where it kind of gets really lame. I had to buy 3 for each rack and cut the remaining inches off to fit them all in. It looks flush but I paid for 2 more strips just to cut a portion and throw away. Meh So aside from that, they work great. Provide extra cushion for whatever I throw on top. The whistling is non existent which is what I am really happy with. I wish they would create more custom sizes but whatever. 6 bucks for 15 inches, it wasn't as bad as I thought it would be. Still better than paying for 400+ dollar rhino racks!

Product quality was as expected, but length wasn't. The expanded product detail is the only place you'll find that this isn't a full length strip. Pricing is per 15 inches resulting in a much higher cost than buying a 48 inch strip from Thule or elsewhere.

This product fit perfectly in a 2022 Tesla Model Y's OEM Roof Rack. Removed the rubber strip from the front rack only, and replaced it with three of these Rhino Rack M626s side-by-side, trimming the third one slightly to fit. The whistling noise previously present when driving over 40mph from the OEM Roof Rack is now gone. Relatively inexpensive solution, and even looks cool. EDIT: The issue remains, but typically only after 60mph. At least it's an improvement, but not solving the problem on the highway. EDIT 2: I combined the three M626s as before, but also wrapped a paracord eight times around the front roof rack only, and the whistling noise is gone. Tied the paracord down on both sides around the wingnuts that hold the roof rack down to the vehicle. Cheap fix, looks fine. EDIT 3: The noise was intermittent even with the paracord. I took the roof racks off. Good luck.

My Subaru Forester OEM Fixed Roof Crossbars had considerable wind noise, so I took a chance and bought these to replace the OEM smooth rubber insert on the top of the bar. The OEM strips were 12mm wide and the Rhino strips were a perfect interchangeable fit. I was able to remove the OEM strips and insert the Rhino strips in a matter of minutes and without any tools. My objective was to reduce the wind noise. I was (and still am) amazed that these Vortex Generating strips COMPLETELY eliminated the wind noise. I am very pleased with the results.

Toujours bon d'avoir des bandes supplémentaires qui en plus s'insèrent dans les conduits du rack

I don't even see the point of selling these I assumed it was 400cm {enough for 2 standard racks) not 400mm the ad is misleading. Don't be fooled like me!

It s ok, it work but 25$ for that short piece of rubber is to expensive

Great product, easy to work with and cut to lenght, I wish they were longer than 14" strips. *** they have a MSRP of 1.75$ each strips, I suggest you look on the manifacturer for a local reseller. I originally bought 2x from amazon and returned them and bought 6x locally for the price of 1 on amazon***

Le bandes ne font pas la pleine longueur du support. Pour le coût quand même important, je m'attendais à remplacer toute la bande et non que le tier de la longueur du support.