CURT 13068 Class 3 Trailer Hitch, 2-Inch Receiver, Select Honda Odyssey

For less than $130 delivered I bought from Amazon Prime the Curt 13068 Class 3 Trailer Hitch for my 2013 Honda Odyssey EX-L. My decision was based on the 450+ Amazon customer reviews yielding 4.5 stars. The package arrived 8 days after ordering in a huge heavy duty box containing the undamaged, unscratched trailer hitch, all of the required hardware and a couple of pages of installation directions. I watched about a half dozen installation videos on YouTube and was convinced that I could easily install instead of paying our mechanic $225+ for installation. I was able to install without jacking up the van using about as half dozen typical tools: 19mm socket. 11/16” socket, ratchet, extension a couple of flat blade screw drivers, a can of WD 40, a borrowed torque wrench and a 12mm x 1.25 thread tap (Vermont American 21146 12MM-1.25 High Carbon Steel Metric Spark Plug Tap purchased for $8.38 from Amazon https://www.amazon.com/gp/product/B000K1LZVM/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1) I laid out a 8 bricks behind each back tire (1 layer, 2 bricks lengths wide and 4 bricks deep) and backed the van up on them and set the parking brake This safely provided an extra 2” of lift on our level and flat concrete driveway. After ensuring that the van was rock solid I began working underneath. The installation took me about 45 minutes but I just took my time. My thought is that the project is about 1.5 - 2.0 beards on the "Revzilla Motorcycle Parts" Beard of Difficulty Scale (1 beard = easy, 3 beards = maximum difficulty). Simple installation as follows: 1) REMOVED THE DRIVER’S SIDE PLASTIC PANEL. I removed all the pop-fasteners as suggested. Since the panel was to be discarded I merely broke the panel off of the rear 10mm screw and Philips head screw behind the mud flap ( which saved about 10 to 15 minutes.) 2) REMOVED 2 EXHAUST HANGERS: Sprayed the 2 exhaust hangers with WD 40 and then easily pried off the 2 exhaust hangers. 2) CLEANED THE WELD NUT THREADS: Using the 12mm x 1.25 tap I begin cleaning out the 4 weld nuts holes. It was difficult to get the tap started so I used one of the bolts to clear out the first few threads and then used the tap. Unfortunately I thought the square end of the tap would fit in one of my 12 point sockets but none worked so I had to use an adjustable wrench which would only make about 1/3 revolution before readjusting. This took about 15 to 20 minutes. Even the threads beneath the old plastic panel needed cleaning. 3) FISH THE CARRIAGE BOLT & FLANGE THROUGH THE DRIVER’S SIDE FRAME RAIL: This worked like a charm. Threaded the fish wire to the bolt, added the rectangular flange, double-crimped the fish wire to keep the bolt and flange close together, fished the surplus wire through the larger hole through frame rail and out the target hole, pushed the flange into the larger hole, then the bolt with the attached fish wire, pulled the entire assembly through and out the target hole; left the fish wire attached to the in-place bolt for further use. This literally took about 2 minutes. 4) LIFTED THE HITCH INTO POSITION FOR BOLT INSTALLATION: Using my motorcycle floor jack I lifted the hitch into position, first sliding the passenger side of the hitch above the exhaust pipe and then after pulling the still-attached fish wire through the target hinge flange hole completed lifting the other side with the jack until I was about 1/2” from the weld nut holes. Starting with the exhaust pipe side I loosely attached 2 bolts and washers into the 2 corresponding weld nuts, attached the nut to the carriage bolt and then loosely installed the 2 remaining bolts and washers into the 2 corresponding weld nuts. After visually checking to ensure that everything was lined up properly I tightened all and torqued as suggested. The hitch looks like it was custom welded to fit my van. It bends around the exhaust pipe and gas tank and wastes no space between the top of the hitch and the bottom of the bumper. EVERYTHING lined up perfectly and easily installed as suggested. Curt really nailed this product! I would have paid twice as much for this level of quality and installation ease. A few observations: A) If you don’t have a can of WD 40 laying around, get one. This DEFINITELY made the job easier. B) Definitely temporarily unhook the 2 exhaust hangers. This makes the entire installation a breeze; it takes about 30 seconds to reattach both hangers. C) I wish that I would have bought the small, cylindrical brush to clean the weld nut holes. There was a lot of debris that impeded the tap and required removing and cleaning the tap. D) I wish that I would have popped off the plastic panel a few days before installation and soaked with WD 40 and wire brushed the weld nut threads a few times before my installation day E) Definitely watch some hitch installation YouTube videos for your vehicle. No need to reinvent the wheel here. A few installation photos attached Tomorrow I'll be installing the Trailer Light kit (about $40 on Amazon)

Hitch purchased for a 2007 Honda Odyssey - was about $40 less costly than the Hidden Hitch and DrawTite counterparts. Fit and finish was excellent and it appears to be a well made and engineered product. Also Curt provided some of the best instructions I've seen on a product like this. Thorough, in well written English and with color photos to boot. As other reviewers have pointed out this Curt hitch only has 5 bolt points (4 into factory weld nuts and one more on the drivers side thru a frame hole) compared to the factory/Hidden Hitch/DrawTite hitches which use all 6 of the factory chassis weld nuts. Since this hitch does not use the two forward most weld nuts Honda builds into the chassis, it has much shorter mounting ears than the factory/Hidden Hitch/DrawTite versions making it a lot easier to maneuver into place, plus I found there was no need to unhook the tail pipe. As I am only ever going to use this as a mount for a bike rack I have absolutely no concerns with the 5 bolt points vs. 6, however if you are going to do a lot of heavy towing - even though this hitch is rated the same as the Hidden Hitch/DrawTite - you might want to consider opting for one of those versions which have the 6 bolt mount and spread the load out a bit more. In regards to the install it went extremely smoothly and I did not require any assistance. As many other reviewers have mentioned - get yourself a tap and clean out the weld nut threads first - do not skip this step!!! My 2007 Odyssey needed a 12mm-1.25 pitch tap for the weld nut thread clean out. I thought I was going to strike out finding one locally (no luck at Home Depot/Lowe's/Auto Palace) but found one at PEP Boys for under $5 and it even came with a drill bit (which of course you don't need for cleaning out existing threads). It was a Kawasaki brand model 840493. Again, do not skip this step! After lubing the threads and tap with some WD-40 or equivalent, it is easy enough to do - just be careful not to cross thread. I used a T-handle for the tap and found I had sufficient clearance, although on the passenger side the tailpipe needs to be pushed out of the way - I used a piece of rope to to tension the rubber mount and hold it out of the way while I ran the tap. On one of the weld nuts I neglected to drive the tap far enough and must have left some rust in there - this became obvious when I went to install the mounting bolt. It started easily but soon bogged down, and having seen my share of galled and broken bolts I could feel I was starting to risk a problem - out came the bolt and I re-ran the tap making sure to drive all the way through the weld nut well past the tapered area of the tap. After that all the bolts could be threaded into place by hand. So yet again I urge you to not skip this step! If you do you risk breaking the weld nuts and/or the bolts and causing yourself a great deal of hassle. Clean out those threads and make yourself a happy hitch installer. To mount the hitch there is no need to jack up the Odyssey. After cleaning out the weld nut threads, I started by hooking the passenger side flange up over the tailpipe. Then I rolled over to the driver side, lifted it into position, held up the hitch crossbar tube with my leg while I hand threaded in the two bolts finger tight. Returned to the passenger side and threaded in those two bolts finger tight. On the driver side, Curt provides one more bolt, nut, spacer and a special fish wire - just follow their excellent instructions and you will have no trouble with this. Finally, I torqued to specification - 72 ft-lbs on the weld nut bolts and 50 ft-lbs on the 5th bolt. Wow that was easy, all told I think it took 30 minutes or so. In summary, a very nice hitch with great instructions that's easy to install and IMO is perfect for light towing and especially ideal for bike or other racks.

The end result is a 5 star hitch- exactly as advertised. High quality, strong/sturdy, can be installed by one man. I gave 3 stars on the instructions and ease of install, because the instructions omitted some additional detail that would've helped, and I received a hitch that had to be hammered into the proper alignment. Minor adjustments to their documentation would make this an easy 30 minute install. It also saves time to take a tool inventory before it arrives. A couple things to note when you order: -You can technically install this without lifting your car, but it makes it easier if you can give yourself an extra couple inches. The easiest/safest way if you don't have a pro setup, it to set up a pad of bricks for the rear tires to park on- then block off both sides of the front tires and you're set. -Make sure you have a torque wrench that can be set from 70-86 ft lbs. They start around $25 on Amazon if you can't find one to borrow. It takes some strength to reach that level with a short torque wrench- most regular men can do it, but if necessary, find a longer one that'll provide more leverage. -You'll also need a stub phillips screwdriver or a phillips bit on a wrench (there's only a few inches to remove a screw between the fascia and the LR tire) -Need a regular 10mm socket and a deep 19mm socket. You can manage the 4 main bolts with a standard 19mm, but you'll need a deep socket for the 5th and final bolt (especially when torquing it). -You'll need at least a 6" extender for the 10mm socket -There are 5 fasteners connecting the fascia covering the driver's side rear frame that you need to access. 3 are those plastic push and lock fasteners along the rear half. Then there's one screw (need short phillips screwdriver noted above) and one hex screw (10mm socket and extender noted above); both of these are on the front end of the fascia right near the back of the LR tire. This is the only time you'll need to slide further under the vehicle. I broke the plastic fasteners trying to get them out, so I'd buy 3 extra ahead of time for when you reinstall the fascia. You'll need to trim the fascia when you're finished to reinstall it- so have some strong snippers ready to cut thick plastic. -When I first lined up the hitch, the holes in the hitch were too narrow to line up with the frame. This was an inconvenience but fixable. Have a 4+ lb hammer on hand to hammer the hitch into the correct width if necessary. Alternate hits on both sides, and hit it HARD. Took maybe 20 hits total to get me the extra 3/4" I needed to line up. -You don't need to detach your exhaust, but you'll need to force it out of the way when installing the two passenger side bolts. I could move it just enough to torque each one. -Not required if you torque properly, but you can use thread locker on the 5 bolts. I used purple vibra tite- very cheap for the smallest tube and a little easier to remove if I ever need to. -As they mention, start by inserting the hitch over the exhaust. You can rest it there. I used my leg to raise up the other end to make it a little more level. I started by hand threading one bolt on the exhaust side several turns so it could support the hitch. Then I did the same on the driver's side. That's the easiest way to do it quickly with one person. Once two bolts are in, it's cake. The fishwire technique for the last bolt is well described in the instructions. -Our van has about 80k miles on it, but the bolts all threaded easily into the frame with some WD-40. I tested all first. Others have noted that they needed a tap and/or thread cleaner before starting though, so keep that in mind.

I recently purchased this hitch for my Honda Odyssey, and overall, I'm satisfied with the product. The installation process went quite smoothly, with the hitch fitting well onto my vehicle. The design and build quality seem robust, ensuring it will serve its purpose effectively for towing. However, it's worth noting that the hitch is quite heavy, which posed a slight challenge during the installation. Lifting it into place and securing it with bolts required some awkward maneuvering. My recommendation for future buyers would be to have a friend assist during the installation to make the process more manageable. Despite the weight challenge, having an extra set of hands can turn what might be a tricky task into a much smoother experience. In comparison to a different hitch my brother purchased for his Honda Odyssey, I feel fortunate with my choice. His hitch had alignment issues, making the installation a complete disaster. In contrast, this hitch's holes lined up perfectly, saving me from the frustration my brother faced. Despite the weight factor, I consider this hitch a reliable choice for Honda Odyssey owners, especially when considering the potential pitfalls of alternative options in the market.

I purchased this hitch for a 2001 Honda Odyssey, in preparation for a road trip where we needed to take 5 bicycles with us. In the past, when we've taken these trips, I used a hatchback mounted bike harness to hold three of them, and put two of them in the van itself (taking out the two middle seats). While this worked, it was extremely uncomfortable for all involved, but for ~1 hour road trips, we made it work. This time around, we were driving further (~5 hours), we needed to do something different. I decided to put them all in the back using a hitch and 5 bike harness (http://amzn.com/B00TRTT178), saving us the extra room in the car for people. I installed the hitch myself in a 14 year old Honda, in my garage, without a lift, all by myself, in about 2 hours. Some key points: - Watch the instructions on youtube (there are many of them, but I found this one -- https://youtu.be/tzI9FeUx-e0 -- to be excellent). - For an older car (like mine), the nuts in the car will be rusted. A wire brush will not be enough (I tried). A tap is the only thing that will work (I got mine from amazon - http://amzn.com/B000K1LZVM ) - It took me at least an hour, may be an hour and a half, to clean out all 4 nuts so the bolts will screw in, due to a combination of things: -- I didn't have the right handle for the tap (by mistake, I ordered a 1/4" handle rather than the 7/16 handle that's required, so I used a adjustable wrench, which made it harder). -- it was the first time I used a tap, was going slowly to make sure I did it right -- the nuts themselves being very rusty, took a while (and some serious elbow grease) to get the tap in there -- I didn't move the tail pipe out of the way, the space was tight but very workable (it's the original one, I was worried that it would fall off due to all the rust, I didn't want to put extra pressure on it) -- the first three were quite quick and easy (less than 10 minutes per), the last one didn't cooperate (of course, isn't that always the case!) Once the screws fit easily into the nuts, mounting the hitch itself was very easy, something I did easily by myself. The fish wire makes installing the 5th bolt trivial. I hooked one side of the hitch over the tail pipe, put the screws in on the other side (lifting the hitch using my knee to hold it in place, then I screwed in the passenger side, then I tightened everything by hand. I'll definitely get a hitch for the next car I buy -- but rather than paying a ton for the dealer to install it, I'll do it myself!

Good product, is working well for me. I only gave it four stars because the installation was a little more complicated than expected. Another reviewer had mentioned "tight tolerances", well mine had negative tolerances. Holding this up to the frame, it didn't line up with all the holes. It appeared to be about an inch short which was too much of an angle to have any chance of threading the bolts in. I tried partially remounting it several times thinking I might be doing something wrong. Then I double and triple checked to see if I ordered and received the correct part. In the end, I just mounted the first side (exhaust pipe side) hand tight then fed a tire iron through the third mounting hole on the second side and up into the third mounting hole on the frame (the one without threads). I leveraged it over and screwed the other two bolts in by hand. Not a major problem but it wasn't expecting this and it did through me off a bit. Other than that, installation wasn't really that hard. I did it by myself. The instructions suggest a helper might be a good idea and I'd have to second that recommendation. However, I've never done anything like this before and managed it all by myself so don't let that hold you back. I got a Curt bike rack along with this and I gave that a full 5 stars so I have no reservation recommending Curt products. Get under you car and look at the bolt holes this will be mounted to. Many reviewers recommend getting a tap set to clear the threads but you may not need it. My car was 5 years old and the threads were fine. I ran a basic wire brush in a couple (a small plumbing brush) but then didn't both for the rest and had no problem. Because it was so strongly recommended in the reviews, I bought a tap set just to be prepared but it ended up being an extra trip to the store to return it. Fishing the bolt and washer up through the frame for the third bolt hole on the second side was easy and the included wire they provided to do that worked exactly as it should. There are videos on the Curt sight and on youtube that show the installation process. I found them to be helpful, check them out.

I was amazed at how easy it was to install this on my 2010 Odyssey. Watched a YouTube and only needed a couple of tools. Done in an hour.

I put this off as long as we could now the kids bikes and ours have outgrown the van. First and foremost this is a high quality Made in the USA hitch, class 3 item. It arrived in a super sturdy box hardware securely tapes to the item so as not to float free in the carton and scratch the hitch( not that it would matter) great packaging. I dragged it out to the garage, it is large and heavy no surprise there. I matched up the holes and inspected the bottom of the vehicle before starting so I could dive right into the install. All was good and I sprayed a little wd-40 into the threads just to flush any unseen debris out. Mind you my van is an 02' 11 years and 160,000miles of road use. I have decent to above average mechanical skills, limited tools but a logical mind. That being said this is as easy a job as possible. I had a paint can handy to support the side of the hitch I was not bolting up. No need to jack up the car, or drop the exhaust, I did not have a 9" extension for my socket and it probably slowed my process. But it only took 30 minutes regardless. Step one-fillet the box flat, slide under back of car with hitch properly aligned under car...(kept me off the concrete and from scuffing hitch on pavement Step two-prop up driver side of hitch on paint can below holes in frame...scurry to passenger side maneuver hitch mount around exhaust and hand thread two bolts and washers... Step three- back to drivers side lift and tighten completely two bolts and washers... Step 4- fish included wire into the large hole adjacent to small hole aligned with hitch plate( so much easier than it looked and the wires included) thread spacer on to wire 90deg bend in wire, spigot into coiled end, and pull through. Unthread wire from bolt don't let the bolt go it will hide in frame, hand thread nut on. Step five- go back tighten everything to the specified torque for safety, Step six open a beer, except I did it at 7am so I had another cup of coffee. The hardware was exact, the manufacturing perfect, paint solid, and instructions well diagramed and photos to match each step. Why I waited to do this was besides me, Honda quoted $350 for this PepBoys $250 for the price of parts and my labor I cut those virtually in half. And this hitch is Made in USA and higher quality than their offerings. I think I spent more time reading the instructions than installing so as not to have to go back to read them again, there are only two sizes or socket needed and hardware was clearly packed with an inventory sheet as well. It also arrived a day earlier than promised, good for me but be aware these are prompt shippers.

Perfect fit on my 2015 Honda Odyssey. Needed to use a M12 x 1.25 Tap for the holes on the exhaust side, as they were fairly rusted. So definitely look into added that as a purchase if installing yourself. Including taping the holes, took about an hour to install.

Muy fácil de instalar!

取り付けられません

perfect fit

100% recomendable, cómola mayoría de artículos que se venden por Amazon, el paquete llego en el tiempo prometido y muy bien empacado, en cuanto el artículo les comento que el enganche ajusto en mi Odyssey modelo 2012 perfectamente y es muy fácil de instalar, tan es así que la instalación la realice yo solo sin la ayuda de nadie más, creo que eligiendo el enganche correcto para tu vehículo no deberás tener problemas de instalacion.