24 x 8 Inch Rectangular Drop-in Fire Pit Pan with H-Burner, Gas Fire Pit Insert for DIY Fire Table, 304 SS, 90,000 BTU Max

This was my first fire pit build. I had some old deck boards from when I remodeled my deck and put together a concrete top to hold the pan. The Pan was extremely easy to install. Instructions were clear and shows connection options for both LP and NG. I have it temporarily hooked up with propane until I run the natural gas line to the location. As you can see in my video, it has a really stout flame. The 90k BTU provides plenty of warmth and the flame is really consistent across the entire burner. I don’t have any complaints about it. I did get a little discoloration on the edge of the pan where the flame drifted due to the slight breeze we had. Probably because of the propane vs natural gas. However it cleaned off easily. My only recommendation would be to buy a multi-turn valve vs a quarter turn valve. I bought the Stanbroil quarter turn valve and it doesn’t allow much fine-tuning of the flame. It is nearly all or nothing. And the “all” is a huge flame. My video shows about the minimal flame I could achieve the quarter turn value. So if you want a small flame, keep that in mind. On another note. I purchased both the Stanbroil valve and electric ignition that were recommended. Neither come with documentation for install or operation. I had to kind of figure it out. But was not too bad. The pan comes with a plate for installing the electric igniter, but doesn’t say what it is for and does not provide the screw to mount it. Luckily I had some stainless steel hardware on hand. Once installed it worked flawlessly however. I would recommend this product. It is a Good value, easy to install and provides a great flame. I am happy with it so far.

Great quality and packaging.

I'm a fabricator and was VERY impressed by the fit, finish and quality of this unit. The dimensions are VERY tight and what is listed. Unlike most products you can't trust what it listed, you can bet your life on these dimensions! Installed easy, looks great and works perfect. Will be buying more soon!

It’s pretty good. It functions and was almost exact on the measurements. I’m glad I added a bit of space in my build (1/8 inch) so that wasn’t an issue. The only downside is that it’s not exactly flat. So when it’s sitting on the table one corner or the other is slightly elevated. It’s minimal, but just enough to snag a napkin or cloth. I quadruple checked with multiple levels- my table is flat, the burner is not.

This insert was perfect for this project. We were looking for an outdoor table/ firepit combo piece and couldn’t find what we wanted, so I built one. I did a little bit of research and it turned out perfect. The top is concrete countertops. The opening for the fire pit is 1/8” larger than the insert. It has a flange on the outside so you can go a little larger to cover up the edges of your top. This will help prevent any buckling when it heats up. It is hooked up to a LP tank. I did purchase the air flow valve and that creates about 1 1/2 ft. flames. That’s a little too much for our area as it’s in a screened porch. It also puts off a lot of heat which is nice. It also fits a 40lb bag of glass perfectly. The items for the fire pit were purchased off of amazon. The 40lb. bag of glass was fair in price and came in 1 bag.

Run the biggest gas line you can and get the biggest gas valve you can for the biggest flame. This is with a 1” line all the way back to the meter and 3/4”gas valve. Neck down to 1/2” inlet at the bottom of the pan.

I'm super pleased with this purchase of the 36"x12" fire pit burner. Very good build quality and was packaged safely with foam on the corners to prevent bending. I also bought the "no whistle" metal hose to go from the key valve to the burner and it works perfectly. Make sure your bends in the hose are nice and smooth and make the radii as big as possible to prevent whistling. I'm fueling my fire pit with propane at the moment and at some point will plumb it into the natural gas supply in my house. I made sure to install a mixing venturi to allow the propane to provide a better flame with more oxygen. I constructed my 48"x24" fire pit with 4" limestone stacked 4 high. I also made the concrete top that is 56"x32" which provides a nice border around the burner pan to place drinks or a dinner plate.

This was way easier than I thought to build and I saved a lot of money. If you’re handy at all this is a simple but awesome way to upgrade your back yard. Highly recommend

Muy buenos productos, excelente calidad.

Very nice high fire

Well built and throws a lot of heat. The included igniter / thermocouple cover plate matched perfectly with the igniter that I ordered separately. I just had to drill a hole for the t/c probe. Very nice flame with lava rock

I first ordered the 18” round burner to complete a do it yourself natural gas fire pit with round stone base. After having extra stone wall units,I quickly fashioned a base rectangle for a more modern clean look and then ordered the Stan broil 30 x 10“ drop in pan and could not be more pleased with it. Highly recommend this product. It puts out some serious heat. Nelson

Burners discoloured fairly quickly.