🔧 Control Your Power Like a Pro – Rain or Shine!
The Paddsun 60A Drum Switch offers robust motor control with a 3-position Forward/Off/Reverse hinge lever, rated for 60 amps and 120 volts. Its IP65-rated, impact-resistant plastic casing ensures reliable operation in wet or harsh environments, making it an ideal panel-mount solution for professional-grade electrical motor control.
| ASIN | B07WYHRHHG |
| Actuator Type | Hinge Lever |
| Best Sellers Rank | #204,671 in Tools & Home Improvement ( See Top 100 in Tools & Home Improvement ) #121 in Electrical Motor Controls |
| Brand | Paddsun |
| Brand Name | Paddsun |
| Circuit Type | 3-way |
| Color | Green |
| Compatible Devices | Electric Motors (3HP 120V or 6HP 240V) |
| Connectivity Protocol | X-10 |
| Connector Type | Din |
| Contact Material | Plastic |
| Contact Type | Normally Open |
| Control Method | Touch |
| Control Type | directional |
| Current Rating | 60 Amps |
| Customer Reviews | 4.1 out of 5 stars 169 Reviews |
| International Protection Rating | IP65 |
| Manufacturer | Paddsun |
| Material Type | Plastic |
| Model | EM-J015 |
| Mounting Type | Panel Mount |
| Number of Items | 1 |
| Number of Positions | 3 |
| Operating Voltage | 120 Volts |
| Operation Mode | ON-OFF-ON |
| Part Number | EM-J015 |
| Specification Met | Ip65 |
| Switch Type | Hinge Lever |
| Terminal | Through Hole, Spade |
| Unit Count | 1 Count |
| Wattage | 22800 watts |
R**S
Working well
Nice part great part
D**G
It works
It works after you figure out how to wire it. I am not electrical savvy. All I need is two 12 volt wires in and two motor wires out. I used the info below.
B**N
Worked for Reversible AC Motor Switch.
A more clear wiring diagram and basic instructions would have been nice, but I figured it out. I needed to wire a reversible switch to an AC motor that had the six wire configuration - 2 wires need to be alternated to different wire bundles. The easiest way I could figure was running 2 extension cord lines to the switch from the motor. Black and white wires used as alternating switched wires, then I used the green wire as the power circuit. Worked like a charm. Pic shown for others who may have the same need.
E**D
English translation but,Not enough room for wires,
120 v, reversing motor for lathe The first problem is The directions all in Chinese. Attached is a translation. Second is that there is not enough room for #10 wire, forget about wiring for 60 amps. I had to crisscross the wires over the drum to get them to fit, not the best way. And the little grommets are a joke. For proper wiring, you need cable clamps but it is still a very tight fit. Once wired, the switch works fine
R**W
Motor Reversing Switch
I needed a reversing switch for a split phase motor I use on a small belt sander. This switch was priced much more attractively than the metal cased ones I bought years ago and are now much more expensive. It took some figuring out how to wire the switch. I basically ran the two wires that are swapped to reverse the motor from the motor to the switch and then back to the motor. Another set of contacts were used to connect the hot wire to the running coil. It works perfectly for me in this application.
T**I
No wiring diagram
Bought for a davit & wasn’t able to get it wired up due to a lack of instructions, diagrams. Had an licensed electrician look at it & all he could say was “good luck”. Thru it in the trash.
A**R
Check your wiring before blaming switch.
It works perfectly. Great deal at this price. I think a lot of negative reviews happen because wiring can be tricky and it's easier to blame the switch than your own mistakes. This really is a good switch.
A**R
Switch
As described
Trustpilot
1 month ago
1 month ago