Flashforge PLA Filament 1.75mm, 3D Printer Filaments 0.5kg Spool-Dimensional Accuracy +/- 0.02mm for Adventurer 3 Series (Orange)

It's expensive for half kilo of filament, though there are ways around that if you don't mind having a 1 kilo reel outside the Adventurer. However, this filament has always worked well for me. Never any issues at all after 3 or 4 reels now. I don't print daily, so the cost difference doesn't really affect me. A reel lasts me months. Have had zero problems with adhesion and never any breaks or jams. So I'm fine with it.

I’m more of a gamer than I am a 3-D printing hobbyist I just want the 3-D printer to work. I don’t want to monkey around with it. I can print great quality miniatures with this PLA on my Flashforge Adventurer 3. This is the brand I’ll be sticking with for as long as I own my FFA3.

so I bought a few different colors to try and see how they look. I have only used the red and orange so far and I like the color but not the transparency. at .8mm wall infill shows right through the wall. at 1.2 its noticeable but not to bad. at 1.6 it was just about solid color with little infill showing through. Since this was the first time using this filament I like to watch the first few layers go down to make sure its lying down a good first layer. this is almost impossible since the first layer is almost clear. the next 4 layers are just as bad not being able to tell if it is under extruding or over extruding without rubbing your finger across the surface. at .8mm bottom layer you can see the the metal base through my glass bed kind of like looking through tinted glass. over all not bad but will be looking for a more solid color

Surprised these people don't sell it as pla+ will absolutely buy again, very strong, printed perfect.

I bought this transparent filament for my Flashforge printer. It was nicely packaged and properly wound. I had literally no problems whatsoever using this filament. No snags, no clogs, exceptionally even performance of the spool across multiple prints.The price is good and the quality great. I literally just opened up the bag, slapped it in the printer, do a filament change and then it's off to the races. Even though transparent filament is really difficult to make "clear" due to multiple layers/infill, I really love the way this transparent filament looks and this brand has become my go-to.

according to my son, it fits very well and is very easy to install.

This is a good quality product. The color is spot on from what it pictured and even looks better on my 3d prints. I've tried many other products and this one by far is everything advertised and even better then advertised. Will continue using this product.

The worst PLA that I’ve worked with. From straight out of the packaging it was difficult to work with. I’ve been printing for 5 years without a problem and this filament roll has provided me with 4 failed prints in a row with the issue being it gets jammed up when being fed through my Ender 3 V2 printer.

Excelenteproducto

I've used FlashForge PLA before and it's quality never disappoints. It's a great standard run of the mill cheap PLA. Perfectly adequate or even excellent for most prints. Easier to print than other PLA filament I've tested.

Dieses Filament verfügt über keine ausreichende Haftung auf demDruckbett. Im Vergleichstest zu dem orangen Filament vom gleichen Hersteller haftet es überhaupt nicht unabhängig von den gleichen Druck Settings.Mehrere Tests ergaben, dass die Fehlerquelle hier ds Filament selbst ist.Schlechte Qualität! Finger weg bei dem Preis.

First of all, getting the important bit out of the way: Treat this like any other PLA, it doesn't need special treatment.I was expecting something like a silk pla with more sparkle, but what you get is a very matte black with dull white bits in, I know that's not a great way to sell it, but it just looks... great on blocky prints, when it comes to models with lots of detail this is not what you want to use, it comes out making the print look like it's just a bit dirty!Thumbs up for this stuff, it's great, I wish Flashforge would keep the 1kilo spools in stock because it's annoying having to buy the double-the-price 500g ones.

Ich habe 2 Drucker. Einen Creality Ender 5+ und einen Flashforge Adventurer 3.Auf dem Ender war es nicht möglich auch nur einen Druck mit diesem Material zuende zu bringen. Die Düse war ständig verstopft.Auf dem Adventurer konnte ich immerhin zwei Drucke beenden bevor eine Verstopfung auftrat.Der Effekt im beendeten Druck ist schon nett.Dieses Filament ist schwierig. Wenn es druckt ist das Ergebnis absolut überzeugend.Aber Fehlschläge sind wahrscheinlicher als ein Erfolg.7x Gedruckt 4x Mist.