Nilight 2PCS 42W Flush Mount LED Light Pods Spot Flood Combo Backup Reverse Driving Headlamp Mount on Bumper Grille for 4x4 Offroad Truck SUV

Wasn't too sure about these when I saw them online. I was expecting something cheaply made and something that felt equally cheap in my hand. I was pleasantly surprised when I opened the box and unpacked the contents. Everything was well packaged and nothing was scratched or damaged. The lights are heavy gauge metal body construction and are very sturdily built. I wouldn't recommend using the cardboard template though. U installed the first one without using it and everything came out good. Using the template, the holes were off a little and had to be bored out a little larger in order to get the bolt through the hole. Just slide the light through the cutout you make then mark the mounting holes and drill - perfect fit. I can't wait to see the difference these things make. As you can see in the picture, the bag contains bolts, buts and washers. It also contains an allen wrench to tighten the bolts. I could barely tell when my factory reverse lamps came on. After installing these lamps, I can clearly see when I am backing up. I get great illumination at least 50 feet behind my truck now; more than enough to safely back up without worry. I hope to get a long life of use from these, but if I were still deciding on which set to buy, I'd choose these. As I was installing them, a neighbor came by and said they looked great on the truck and that they didn't look aftermarket or out of place at all. All-in-all I would say the install is fairly easy with minimal "mechanical knowledge" required. Tools required: 4 1/2" grinder to cut through the bumper, needle nose vice grips, marker, drill with bit. On a 1 (easy) to 10 (hard) scale I'd give the install procedure a 2. The last picture shows the lights on. You can see the OEM reverse lights under the tail lights Huge difference. ******UPDATE****** About a week after installing the lights, I noticed one light was not working. I have not figured out yet what the problem is. I was thinking it was shorting out but that doesn't seem to be the problem. If I tap the back of the light, it will turn on (as long as it is suppose to be on). Now I am thinking it is defective.

I have had these lights on my truck for about 1 month now. They are high quality sturdy lights. I did not hook them up to my reverse lights. I instead ran them to the Nilight 4 gang rocker switch so I can turn them on and off in park and drive. When I installed them, I used the included template and taped them to my bumper and drew out the outline. I DO NOT SUGGEST USING THE TEMPLATE. When I cut the holes in my bumper, the size was a bit off causing me to continuously make adjustments by eye anyway. The holes for the bolts were also off and I had to bore them a little larger and then use a bigger washer on the inside of my bumper to secure them. After wired and installed, the lights were a great investment. I live in East Texas and it rains quite a bit and county roads get very muddy. I have not had any issues with these lights. No precipitation building up inside, no shorts, just works everytime. I intend on getting a ranch hand replacement rear bumper and these lights are going right into that one as well. Good buy for the price.

What a great buy, these things are stupid bright and the combo flood spot setup makes them hugely useful. Driving in snow recently they light up the road like daylight.

These are bright, but much more of a scattered flood than I was hoping for there's not much focus if any for the light beam. I have other nitlight lights on another truck they are a little smaller and have a more focused beam to them. Install is straight forward and difficult do to my choice of 1/4" diamondplate on my homemade bumper should be easy on anything else just make sure you aren't planning on cutting the holes with a 4.5" grinder there's no room for the corners to cover any overcut. So I started with grinder ended with Sawzall. They look nice very low profile now I just need to figure out how to keep them from lighting up the sky and keep them a bit more tamed toward the ground. This is not a defect just a flood light with a very impressive spread more than my personal preference

Lights turned out great! And mounting was easy The template that they come with is a little smaller than actual size, but if you just take the faceplate off the lights, then hold the lights up to where you need to cut out and trace them, it is much more accurate. Wiring was easy. For power I ran a power wire to a switch in a cab (also 16 gauge wire if wondering). You CAN wire into reverse lights if you wanna. But it's all preference. As for the durability, there pretty strong. As for the adjustability, you can't move them from wherever you install them at. Like, there just gonna be there. There's no up and down-side to side motion. And this is very versatile, install on anything as long as the measurements are right, you'll be good. Great buy and so far no issues, but will update if so!

Originally bought these for my plow truck, but never got around to installing them. We bought a 36’ diesel pusher RV and had a two week long cross country trip coming up not long after buying it. Knowing I’d be in dark areas and unfamiliar territory, I felt it was necessary to upgrade the junk factory reverse lights by adding these. They look great, don’t flicker, and are very bright at night! So far they still work great with no moisture or water intrusion even after multiple washes and 5200 miles of driving. Came with everything needed to get them installed on the bumper, but did not include any wiring or switches to get the power to them. Great price though and I’ll be buying more for my other vehicles! So far I’ve had zero issues with any of the NiLight products I’ve purchased

I’ve always had good luck with their products in these lights are absolutely fantastic. I have them mounted on my rear bumper. I do a lot of off-road driving and a lot of highway driving especially in the winter months. My first set lasted for four years on my rear bumper and I just now had to replace one of the lights. The seal did fail in moisture got inside, but they still worked. My only complaint would be the wire harness is not at all long enough for a pick up truck. I have a 02 2500 ram long bed and I had to add about 6 feet to the harness. I’d rather cut off some excess than having it too short. But these are super simple to install very user-friendly and like I said you get a lot more than what you pay for.

Needed more back up light seeing as my street has no street lights these are small and compact yet very bright

Se sienten bien aúno los instalo pero se ve de buenos materiales después actualizo la reseña

Purchased to install as auxiliary back up lights on my truck. Very happy with them, very bright, nice clean white light. More of a spot than a flood, but really nice lights. Not sure on reliability yet, but seem like pretty decent quality foe the price.

broke after less than a year.. i am unable to claim warranty because i could not find their contact ..order it if you know their contact only

These pods are bright! They were easy to install due to the templates being included in the kit. Great lights.

Muy buena calidad y la luz blanca