LyxPro 4 Channel 3 Pin Multi Network XLR Cable Breakout for Stage Sound Lighting and Recording Studio Male and Female to RJ45 Ethercon, Great for Sound Monitoring, Light Setup

This is a fantastic piece of gear. Rock-solid build, clean signal, and zero noise even on long cable runs. The connectors lock in perfectly and feel like pro studio quality, reliable, sturdy, and worth every dollar.

I've purchased six of these over the last couple of months. I've used all six of the female XLR ends, and I've used only two of the male ends. In all cases I've used the version with 4 wires (fan out) instead of these stage boxes on the other end. So even though I've stockpiled 4 unused male ends, I still find these to be cost effective. I've run 150' CAT6 Shielded Twisted Pair (STP) with these with no noticeable noise or cross-talk, even when I turn up the gain on an unused channel and boost the headphone volume on my mixer. I would guess the cross-talk is at least 80dB down, and that is perfectly appropriate for all of my sound system needs. I've taken most of these apart to drill holes in the back and permanently mount them around the chancels of churches. They are well constructed inside with a good quality circuit board that connects all five connectors. To take one apart, undo the four screws on the end with the Cat6 connector and pull that end straight out so that the front panel with the 4XLRs slides out with it. Then mount the empty box and slide the connectors back in to close it up. I'm also carrying a female box end and a male fan-out end in my mobile sound system. I find it faster and much easier to run a single Cat6 cable compared to running a multi-core snake or 4 mic lines. It is very easy to carry 4 Cat6 cables of various lengths, and use the smallest one that reaches. These make my whole stage look neater.

I purchased 3 sets of these for our church. Reduced the number of long cable runs from 12 to 3. We now have 3 zones to our stage. Reconfiguring is greatly simplified. With shielded CAT6 Ethernet cables there is no noise and phantom power works just fine. I wish these were around when we bought all of those long XLR cables. These also could have been used instead of our 12x 4 snake. I highly recommend and, if needed, I will buy again.

The LyxPro 4-Channel XLR Breakout has been a solid solution for extending audio signals from FOH to the stage via an Ethernet cable. It’s worked well for my setup, but keep in mind that if you need both input and output on stage, you’ll need two pairs. Using a high-quality Ethernet cable is essential to avoid any signal loss—I used a custom CAT6 cable, connecting my Tonor microphone receiver’s XLR output to the LyxPro input. On the other end, I routed it out to the hybrid XLR/TRS port on my travel mixer’s first channel. Great performance overall, but quality cabling is key for best results!

I love the quality

I am currently using a set of these without the attached cables to use on my pedalboard. I have low and high octave sends, a mic send and a in ear monitor return all going through the boxes to our band mixer rack. I wanted someway to make my setup time at shows a lot faster, now all I have to do is plug in a ethernet cable on both ends and I am pretty much done. Less cables across the stage is a huge plus. I am planning to build pedalboards with these on all our band members boards so all everyone will have to do is plug into their pedalboard and run a single ethernet cable. So far they are working great both sending signal to the mixer and returning headphone audio.

No hums. No issues. Just 4 balanced XLR connections running through a single RJ45 Cat-6 Ethernet Network Cable. Really helps tidy up those cable runs.

We ordered these as a quick fix for a multi channel front to back of house need and they work , and work well. We initially installed some extra cat 6 lines for whatever future purposes and they were plug and play. Super simple and worked great. Highly recommend

Exelente producto solo recuerda que solo funciona con cable ftp con malla y conector blindado ya que por la malla se trasmite el pin 1

Recently moved audio equipment to a loft/balcony at the church and DID NOT want to run snake cables along walls and floors - Cat5 happened to be already in the walls, so this seemed the perfect solution. Instructions say to use Cat6, but since it was only a 75 foot run, we thought we'd see how it works - NO NOISE, NO CROSS TALK, WORKED PERFECTLY! You literally just plug a Cat5 into each box and you're done. We fed three instruments UP to the mixer and the monitor output back DOWN on the 4th channel.

Not good

These use 2 cores for each XLR so obviously your audio signal becomes unbalanced and you will hear unwanted noise

Solo hay q tener en cuenta el utilizar un cable ftp o stp con conector RJ45 CAT 6A. Ya que a través de la malla que trae el cable y q hace contacto con el conector, se encuentra y se interconectan lado a lado las tierras de los conectores XLR, sin esto tendremos un ruido hum inminente.