Sequential LED Side Mirror Turn Signal Light Smoked Right Left Lamps Compatible with Ford F150 Expedition, Lincoln Mark LT, Amber

Installed these yesterday. Very simple replacement and great look. Plug and play. Replaced both front and back (left puddle light stock) and everything still works. Probably will come back after some time and weather.

After 4.5 years I figured I'd write a review for these. I can't tell you how much I love these lights, the smoked look, the sequential turn signal, and the build quality are top-tier. I actually attempted to upgrade to the switch-back ones but decided not to and returned them, I kept the original ones I bought in 2019 and as you can see in the video I took today they are still working! Make sure you get a snug connection and use dialectic grease if you want to add even more protection. Happy to prove the other reviews wrong by showing these things off. Great product 100% worth the money.

I paired these indicators with the front facing sequential indicators on a 2011 F150. Installation was fairly straight forward and connections are as the instructions and other reviews indicated. However, if you plan to run the wire(s) for running lights, I recommend just remove the door panel and the three nuts holding the mirror on and remove the mirror from the truck. It takes probably 3 minutes with a 6, 8 and 11mm socket, a t20 bit, and hook to pop cover panels on the door panel. This also affords you the opportunity to most delicately remove the mirror from the internal mount (it just snaps on in 4 paired clips at 2,4,8,10 o’clock positions behind the mirror). If you are like me, I cleaned inside the mirror body, behind the mirror on the door and most importantly I was able to easily drop the running light wire(s) into the wire channel and pull through. It helped to firmly pull the end of the running wire through my fingers to straighten with a slight curve and feed through the wire channel and then tilt the mirror on its mounting end and the wire just dropped out or was within grasp to help pull it through. Once ran, fold excess running light wire back up, reuse the wire tie and when remounting mirror feed through door channel with the mirror electrical connector. Once remounted you can feed the wires inside the kick panel through the door rubber electrical grommet. You don’t ‘have’ to remove the mirror to mount these but I found it less time consuming and frustrating because the wire would bunch up and my fish tape was too big/stiff to make the 90 deg bend in the mirror body when it was mounted. All in all 10min per mirror start to finish with cleaning and even using McGuire’s black plastic restore on the mirror plastics. I chose to hook up only the running light wires for forward facing light and did not install the running light wire for the rear facing turn indicator because I don’t see a need to have bright rear facing lights on at night below my mirror.

Great little, 30 minute upgrade job to add a different look to your truck. The hardest part is getting the mirrors off. I was able to slide my fingers in and lift up on the clips to then pull the mirror off. It is stubborn but it will come off. Then it take a T20 torx bit to remove the back part of the housing. These slipped right in place of the old ones. Only issue I had was that the clip didn't quite snap into place but I was able to pull it from the rear of the unit and it finally clicked in. All in all a great product for the price.

I am writing this review for the RUXIFEY Sequential LED Side Mirror Turn Signal Light (rear of mirror) but it is also relevant to the Ruxifey sequential side mirror LED turn signal (front of mirror). I originally ordered the front-side sequential turn signal but while reading the instructions discovered that to connect it without splicing wires in the mirror housing, I would also need to order the rear-side LED turn signals that have output connectors for the front-side LED (Ruxifey does not supply a pigtail connector – probably deliberately in order to encourage you to also order their rear-facing units). I then ordered the rear-side LEDs, but when I tried to install them found that there were three things wrong (a) the input connector is in the middle, not on the inboard end, (b) the LED unit is much shallower, and (c) the prongs for the input connector are much smaller (please see attached picture). These three things mean that with the length of wire supplied by Ford in the mirror housing, the connector will not reach the input prongs on the Ruxifey, and even if it did, the connector is a loose fit on the much smaller Ruxifey prongs. On the passenger side you can work around this problem by drilling a hole through the reinforcing ribs inside the mirror (see attached picture) and threading the wires through these holes (you need to pop the connector body off the wires first, then squeeze down the spades so they grip the Ruxifey prongs, then thread the wires through the holes before reinstalling the connector body on the wires). On the driver side, even with drilling a hole through the ribs, there is no way that the wire will reach the rear-facing Ruxifey. I found the best solution was to solder lengths of wire to the Ruxifey (see attached picture) and then splice into the Ford wiring (thereby eliminating the reason for buying these the rear-facing Ruxifey units in the first place). In case you forget what goes where, with the Ruxifey unit lying flat on the bench, the black wire goes to the North-South prong and the green wire goes to the East-West prong. All this hassle could have been eliminated if the Ruxifey rear-facing LEDs included a pair of pigtail extensions that adapted their prongs to the Ford size prongs. The actual Ruxifey units seem (at least so far) to work well, but had I realized what a hassle it would be to fit them, I would never have bought them. Also (this is not a Ruxifey problem) getting the mirror glass out without breaking anything is very fiddly – first side took forever, once I figured out how to do it, the second side was much easier.

They look great. Happy with them.

Work great. Been on for 2 years and not a single flaw.

Easy enuf to install. Wish they were brighter tho. Can't really see them in the bright sun

Fits perfect for a 2013 f-150, just be careful when removing the mirror to get at the access screws

Works great

Took a few minutes to fit and they look great!

look great, very bright and easy to install

Bon produit avec bon prix