Keter Heavy-Duty Folding Workbench with 1,000 Pound Capacity - Foldable Work Table for Garage, Woodworking, and Outdoor Workshop with 12 Inch Adjustable Clamps

This work table is great, easy set up, easy take down, very portable, very stable. Worth the price.

I don't usually like to review things like this after only a few uses, so I'll hedge this by saying these are initial impressions after a few weeks, so take it for what it is worth. If things change I will update the review. So far I really like this bench. It is ridiculously easy to set up and even easier to fold. I love that I can fold it and store it, or load it into the back of my truck. I echo what others say about NOT pulling the legs out no matter how badly you want to. Grab the yellow handles, pull the tabs with your thumbs, lift up and let the legs fall on their own. This thing is really sturdy. It says it's good up to 1000 lbs. No idea if that is true, but I weigh 225 and I climbed on it and stood up and it had no trouble holding me. I've used it so far to support long 2X8s I was cutting with the Miter Saw and I've also used it as a table for the saw. I like it because I was able to use the included clamps to hold the saw in place. Generally I’ve used it to hold all my junk and to hold boards steady while cutting with a circular saw. My only small gripes are it could be a bit wider AND it needs a well for nails, screws etc. or drinks. Once folded, it’s really easy to carry and not heavy at all. So far I'm really happy. I looked into building a bench and it would have cost me roughly $50-$60 for parts including casters to roll it. For not much more, I got this.

This table is amazing! No assembly and very easy to open and close. This has surpassed my expectations in many ways after the first use. It holds a lawnmower at the perfect height to work on from a rolling chair. Also not made for but the grip handle is just wide enough for the mower crankshaft to fit through allowing the engine to sit up nicely and somewhat braced. The bottom of the table is nice for holding toos and parts, keeping them away from your project but near when needed as you work. When finished this thing easily folds up and fits comfortably in a narrow spot in the garage. This is probably my best garage by this year!

I'll start with the obvious: This is a very cheap folding work table. Expect the plastic molding to be imperfect. However, I just bought my second one of these and for someone who works on them occasionally, both have been far more functional than I expected for the price. The plastic molding issues are mostly cosmetic, a few stringy strands to pull off when I unpack them. The tolerance in the built-in clamp holders is pretty tight, the clamps are a bit difficult to pull out and put back in to their stowing slots. But, that's nothing. These tables are fantastic, despite the very minor issues above. Fix the above, and you're paying at LEAST 4x the price per table. These fold up into almost nothing. When not in use, they stow away in hardly more space than you'd use to hide a folding chair. They have handles on all sides, and they are light enough for someone who works on stuff to lift easily. The weight is easy to manage. I'm able to hold one of these tables at full arm's length, long enough to turn sideways and slide into a little slot against the wall next to a cabinet behind a desk. They are extremely portable. Taking them up and down stairs is easy, due to flexible handle options on all sides. Two hands, one hand, one in each hand, easy. They unfold instantly. If you don't need to hold a lot of weight, this table goes from suitcase form to functional table in about one second flat. If you need to hold weight, you do have to spend another 10 seconds or so making sure the supportive flaps are locked in. Once they are locked in, two reasonably fit people could dance on top of this table with zero concerns. I use one for my miter saw and once set up, never thought I was using a plastic table. The real kicker is, they also fold back up instantly. You just unlock the support flaps, hold by the correct handles, turn it upside down, and shake. All of the legs fold back up into place, maybe having to nudge one or two to get back to fully folded suitcase form. If I had bigger hands I could easily carry four of these, whereas just one KREG table is my limit. The action of the clamps isn't perfect but it's good enough for what you'd use this table for. The clamps are actually pretty smart, with both clamp parts moving independently on the bar. This lets you quickly expand the bottom of the jaw to make room, quickly slide the bottom of the jaw to meet your part, and squeeze the trigger a few times to lock in place without having a lot of clamp bar sticking out from the table. My only complaint is the holsters for stowing the clamps are too tight a fit, I have to use a trick to get them to fit back in once I'm done. (Release the upper jaw. Slide all the way up. Squeeze the handle just once. Slide the lower jaw to meet it, then it will fit.) I've bought two of these now. The second one is for use indoors, and came in handy to glue up 3D prints and wrap holiday gifts, each time taking less than half a minute to pull out and set up, and under half a minute to pack up and stow. A+.

First and foremost, this is a great work table. Once set up, it’s nice and solid. I have found one downside however. When the table is unfolded, there are two hinged supports on either side of the middle section when it opens up. In order to push the handle into place and lock the table open, these supports sometimes have to be manually pushed outward into their fully extended position. I would recommend caution when pushing these into place! I found a pinch point on one of them and it took a chunk out of my finger about 5mm in diameter so please be careful!

I have 3 of these workbenches. They fold up very compactly, just 4-1/4" thick in a solid 21-1/2" x 33-1/2" rectangle with rounded corner so it doesn't hurt jabbing you when carrying it folded. Super easy to set up (maybe 5 seconds) and also to collapse. When collapses, the legs fold right into the workbench top. Only thing that can be tough is shoving the middle piece in enough to snap to lock. My husband has no problem with it, so probably just an arm strength thing. That middle shelf is convenient. They are extremely functional. I use it for sanding all the time and all my different grits sit on there nicely. I stain using sometimes 4 different colors and the ones I'm not holding in my hand sit there waiting for me to grab them, as are extra rags. Lately I've had my large sliding compound miter saw sitting on one of them. I've had my oldest one for about 4+ years now in a working wood shop and it's just as sturdy now as it was when it was new. No warping that I've noticed. Much easier then the other very popular portable work bench. One of mine has sat in the rain for a few weeks while working off site under no cover. Happy to not have to worry about rusting. There is literally no end to uses not just in the shop, but also the craft room or even gardening shed.

Well designed folding and unfolding mechanism for a compact and sturdy work bench.

Muy buena para realizar trabajos, resistente, práctica y muy portatil

Die Klappbare Werkbank ist eine tolle Sache genau das richtige für Heimwerker super leicht gut zu Tragen L.G. W.K.

I bought this item as I do lots of work around the house and figured it would be handy to have. I am a Dewalt guy but picked the Keter table instead because I like the idea of a bottom shelf and the reinforcing rib in the middle. The bonus is that it also comes with 2 clamps that are pretty decent and lock into the table top fairly securely. The table sets up and folds down quite easily and feels very well built. I ordered this item in December 2019 when it was on sale for $106, but after ordering I found the same table at Costco for $69. I tried to cancel my order but it was shipped anyways. The only difference is that the Amazon table was yellow and the Costco one is red. The Amazon one was eventually returned for a full refund. There are models that have adjustable legs with a reduced weight rating but neither of these have that. When its folded up it has the main carry handle on the side and two more on either end. It weighs about 20 pounds and there are 4 small holes on each end, possible to bolt 2 or 3 tables together. The only complaint is that the legs are a bit floppy when its folded up but nothing a bungee cord can't fix. When folded up, this table is thick enough to stand on its own. So far I have only used it to wrap Christmas gifts on and as a spare table for Christmas dinner.

Easy to put up and Easy to drop down ,plenty of workspace and the two clamps slot in Easy and are very versatile and easy to use ! For me its the best work bench I've had, love it ,also very sturdy too🙂👍👌