SAMA NEVIEW 4503 Mid Tower PC Case, Panoramic Dual Tempered Glass ATX Gaming Case, 4×120mm ARGB Fans with Hub, High Airflow, Back-Connector Ready, Type-C & 2× USB 3.0, 360mm AIO Support, White

This is a great full ATX case. Plenty of room for the installation of my RTX 4080 Super on a ASUS TUF Games Z890 Mother board. The power supply unit installs at the bottom in separate air flow than the main box. Cable management is made easy as you can run everything behind the mother board. The glass is tempered and looks great. It comes with 4 RGB fans that interface though an included RGB hub. The directions that come with this case are not good and provides no guidance on how the RGB hub should be hooked into the mother board. If you get this case use a SATA power cable from your PSU to power the RGB fan hub and connect the ARGB cable from the hub to one of the three prong ARGB connectors on the mother board. You can manually change the colors using the LED button on the front control panel or if you push and hold that LED button for 7 or 8 seconds the mother board can control the case fans colors. Also know, there is no fan speed control for the fans that come with the case, the hub does not have that interface. The fans do keep air flowing very effectively. I installed a TRYX Panorama SE 360 ARGB 360mm AIO and running a full bench test my CPU and GPU temps have never exceeded 65C. Normal temps average around 37 to 50 C while gaming. The fans that come installed in the case are very quiet.

I decided to go with this case for my ultimate build, and I don't regret it a bit. The case looks even better in person, it is big though, and a bit heavy, perfect for me as I like my computers big and imposing. The fans are nice, syncs well with the rgb in my cooler and rams, the light modes are varied and cool, there's multiple choices to make your pc lighting look great. A small problem would be the cable management at the back of the case, the cables come a bit tangled up and you must rearrange everything to make it snug and clean. Besides that I didn't have any other problem and the installation was swift. Totally recommended for its price as the quality is incredible.

This case is large and of good quality. It looked amazing once I was done building my son's PC. There a little unit in the back that all the fans plug into so you dont have to worry about plugging them into the motherboard and having enough slots. it comes with 4 fans preinstalled in the case and the LED colors are good.

I've built roughly 20 PCs in the past two months. I personally run a Corsair 5000D, so I've done more Corsair cases than any other brand, but have been trying a few others out, as Corsair and NZXT want an arm and a leg for their AIO and Fans. The other atrocity with Corsair is them shipping their white cases with basic black fans unless you pay more for the RGB option and then it is their basic RGB fans... I've bought a grip of SAMA PSUs recently, as they have been very reasonably priced for their rated powers and 80+ Gold and Platinum offerings. I saw this case and found that SAMA's AIO was reasonably priced and you could order reverse blades fans at a reasonable price. The case comes with 3 reverse blade fans on the rear to the right of the MOBO and a regular rear exhaust fan. The disappointment came when I opened the back panel to find a 4 fan and ARGB hub that was full before extra fans and AIO. Then I recognized that the ARGB cables all had the ability to daisy chain more, though the pre-installed fans did not, this was a relief. The front panel controls are actually on the base of the tempered glass panel and tucked into the bottom of the case, which was really easy to work with. I thought I would be able to add 3 fans to the bottom, but it looks like I was mistaken. There are only two holes to mount a fan, either 120 or 140 on the lower level at the front, whereas the space elevated below the motherboard has a few screw holes, but I don't think one could mount fans with 1 screw and expect them to be stable. Either way they only had one reverse fan blade fans in white in stock last week, but I had already ordered 2 more today before I started this build. The top cover is mounted with pressure mounts, but they provide two silver thumb screws to secure it, which is nice. They also provide two replacement female pressure mounts in the event one fails over time. Reasonable cable management options and clean finish. This build was SAMA case, PSU, AIO and additional fans. One of the easiest builds, very little tight/cramped spaces and I can't wait til I plug it in and setup the OS and see how it looks lit up.

They packed it well. Case arrived without any visible damage. I got this case for the following reasons: 1. My prebuilt PC case was too small to house an AIO. This case is able to fit my Arctic Liquid Freezer III 360mm AIO CPU Cooler (Top Support). My previous case was a tight fit and the AIO took up a lot of space and was squishing the PSU Cables for the CPU connectors. This case leaves a decent amount of room and the PSU cables is not squish by the AIO. 2. I preferred a Front IO Panel on the bottom of my PC since it will be sitting on my desk. 3. Price is good 4. ARGB fans pretty and this case comes with an ARGB hub 5. It fits on my desk. 6. The amount of USB slots on the IO Panel. 7. This case offers a lot of ways to do cable management in the back of the case. Zip ties and twist ties are included. Took off 1 star only because it's almost perfect, but has some minor inconvenience during the setup process. 1. The back of the PC case, the IO shield port is sunk in and not flushed, making it kinda difficult to line up my motherboard. 2. After turning on my PC, it has a funky plastic smell. Tolerable, but I hope it goes away. 3. I had no idea on how to switch the IO Panel from the side to the front, instruction manual left it, I was able to find 2 screws on the sides of the IO panel. Instruction Manual could do with more documentation. 4. After moving the IO panel to from the side to the front, the cables attached to the IO panel is very short and it was difficult to screw the IO panel back onto the front of the case. The IO Panel cables needs to be longer by like an extra 2 inches. Summary: Good case. Setup and instructions could be improved. Update: The included fans looks nice, but I can't control the speed on them which is useless. I have a I9-14900K CPU which gets hot really easily and I need as much cooling as possible.I will be replacing the default fans with pwm fans.

Why did you pick this product vs others?: Quality build, easy to set up, and an excess of parts required for neat and swift assembly. The fan cables could use some work as they are kind of jumbled up in the back, but they are pre plugged in and twist tied so it wasn't an issue. Managed to get them working first try, and the led options are quite extensive. Also, the case is quite roomy!

This is a beautiful Chassis box. With the SAMA L6 water cooling & all the lights, this case is the only one that has stood as proudly as my old Koolance Chassis Box that I had to finally retire after about 26 years. The only problem I ran into with this Chassis is that the 4 lights inside the box, not attached to the L6 Water Cooler did not initially come on, so I explored the wiring that was hid behind the side cover. What a bundle of wires, I called Amazon for a replacement, coming today, but yesterday I thought, I am going to clean this wire mess up. It really isn't necessary because they will work fine if you connect a SATA cable & attach it to the right end of the holder where all the wires start out from. However, I had already straightened them up, so back on goes the cover & this is a beautiful computer Chassis. Everything fit nicely inside, even my RTX4080 monster video card. I have decided not to send back the replacement box (which I am charged for of course) - Don't get any credit until I return one which I am now not going to do. But I am keeping the replacement & plan to put my last computer board & parts into it to use for a spare computer if I ever am down for some reason.

BIG NOTE!!! For this case when purchased in black! The glass is tinted, the images almost make you think they are clear but it's definitely tinted you can see in the photos. Luckily for me with how easy it is to remove the panels I run it with no glass when I play it. Second note the 3 fans not on the rear of the tower are reverse finned to allow air flow in with the aesthetic of not looking that the fan supports for the motor. Last note when tucking the wires on the black side and you have a larger wad of wires, if sticking out just too far it will push against the panel and it'll not hold on.. learned the hard way. Overall its what I wanted from a case, I wanted to put my 360mm radiator on the side like I have it in this one. Love the glass and how easy it is. The removable corner piece perfect. I like the sneak a fan or hard drive under the bottom little drop shelf there and the hide away everything for your wires. It's also set up for the graphics card to be side mounted I'm definitely considering. The adjustment possibilities for all the fans are great because the holes are slotted it's amazing. Now you can set them to where it feels right rather than it being set although those slots end up making it feel flimsy that's just the other end of the coin when it comes to that. Great for supporting your radiators because most of the time when you have a corner of the case and your hoses coming off the radiator end up hitting the fan and makes you end up needing to try something different. So definitely satisfied, if I get another definitely white but I do love my grey and black theme!