Waveshare 4.3inch DSI LCD Display with Case for Raspberry Pi 4B, 800×480 Capacitive Touchscreen MIPI DSI Display Support Raspbian/Ubuntu/Kali/Retropie/WIN10 IoT, Driver Free, Refresh Rate up to 60Hz

This is a carefully crafted unit, easy to install for those familiar with electronic interface sockets. No documentation for setting up was provided, but then again it's not needed. No driver is needed for it for Raspbian on RPi4, and certainly no driver is available for Kodi and libreelec and hence the screen is upside down if fixed in suitable enclosure compared to the intended position of the enclosure . Touch functionality works, but a little slow at times, but not a real issue. Screen is clear and bright when viewed from above.

Lots of references here to there being no build documentation, which is true. I have added a step by step guide in pictures here and words as follows: Contents: screen kit came with 3 ribbon connectors, screw driver, baggy with fan kit, baggy with standoffs & countersunk screws (for screen mounting), baggy with short & long standoffs with pan head screws (for Pi mounting), screen and enclosure. IMPORTANT - make sure to load your microSD card with the OS of your choice (I used the Raspberry Pi Imager to configure and load Raspberry Pi OS 64bit. When done I installed to the back of the pi. Now you're ready to install 1) Fit short standoffs (4) to the back of the Pi. 2) attach Pi to back of screen using pan head screws. 3) & 4) fit the short ribbon cable to the Pi and Screen - NOTE: one side of the ribbon has exposed metal connection strips, these face in to the board, the headers have a clip that needs to be raised and then pushed back to secure the ribbon. 5) Fit the long standoffs to the screen. 6) Fit fan as shown with the screws and nuts provided (nuts on outside of enclosure)and feed connector through the slot per image 7). 8) & 9) Fit the connector to pins 4 & 6 on the GPIO - first row, second pin in for red (5V) third pin in for black (GND). 10) Gently assemble screen to the enclosure and secure with the countersunk screws. 11) this is what you should be left with. I connected a USB mouse and Keyboard initially to assist in updating and configuring my Pi. After all the updates the touch screen functioned and all was rosy.

Using mine for klipperscreen on an Rpi 3a+ & together they work very well. I like the difference between this & the 7" being that this one does not need an extra cable for power & takes it all from the DSI cable on the Pi. It fits very nicely into a 3d printed holder, but should you wish it comes complete with mounting screws etc to put the Pi on the back. As you can see from the video, the touch response is a tad slow, hence the 4 not 5 stars, but for what I am using it for it's just right. Some people complain that it's not bright enough but that can be fixed from diving into the settings on your Rpi if you want to. For me, I plugged it in & it worked straight out the box, no extra drivers or programming on the Pi needed.

Part of the fun of the Raspberry Pi ecosystem is learning, and you'll definitely be learning and experimenting with this screen because it comes with absolutely zero documentation (there is some online but it is next to useless). I got it all to work in the end after much experimentation with different combinations of screws and pillars and reassembling it probably 10 times. The screen and case are very pleasant, bright, readable even though tiny, and the touchscreen works fine as far as a tiny touchscreen could work with fat fingers. So no problems in the end but definitely a journey to get there.

Excellent quality screen and case, touchscreen is responsive and works well with Moode audio. I did however have an issue with the touchscreen initially which was cured by changing the cable, fortunately I just happened to have one from another screen otherwise it would have been a big issue.

Very nice piece of kit and needs zero config on a Raspberry Pi - very bright clear screen - the fan is quite quiet - but be warned there are no instructions, so unless you know your way around a Raspberry Pi it could be tricky to get set up, especially for beginners!

I've had previous experience with Waveshare displays and I am happy to say that my faith in the brand remains undiminished. I'm in the process of using this with a Pi 3A and the amazing Peppy Player to create an internet radio player. Set up was easy and it feels solidly made and works well.

Easy to set up on the RPi4 touchscreen works well, good picture. Documentation is easily found online along with technical drawings for incorporation with 3D printing projects.

Geweldige display . Deze word gebruikt om de Victron venus os te draaien op een Raspberry pi4b. Werkt gelijk zonder probleem. Let op als je dit gaat gebruiken er voor. Venus os geeft alleen bij op start de logo Victron. Je moet inloggen en de unit activeren aangezien de venus os van uit gaat geen Display aanwezig is. (Je heb beeld met de Victron logo)

Ekran na raspbianie dziala od razu po podlaczeniu, nic nie trzeba ustawiac. Wentylator na zdjeciu jest podpiety do zlych pinow, prawidlowo w dolnej linii 2 i 3. Koniecznie trzeba dodac radiator do procesora, inaczej wentylatorek nic nie pomoze. Obudowa moglaby byc aluminiowa, wtedy warto by bylo nawet doplacic, ogolnie spasowanie 7/10.

Avis pour le 4.3" DSi LCD (with case) Super boîtier qui fait très bien son travail. Il est en plastique mais ce n'est pas un plastique dur et cheap, c'est du plastique assez qualitatif. Il s'ajuste parfaitement à mon RPi4b dans la mesure ou j'ai réussi à le monter sans trop de difficultés et sans aucune notice fournie (il suffit de réfléchir un peu contrairement à d'autres qui ont fait un vrai Picasso avec ce boitier...) l'écran est de très bonne qualité, suffisante pour afficher une image plus que correcte. Dans mon cas il fait tourner mon serveur Home Assistant et l'écran n'est pas vraiment utile, il est vrai. J'ai mis des photos selon les étapes de montage si ça peut en aiguiller certains. ATTENTION le ventilateur ne se branche pas sur les 2 bornes sur lesquelles il est branché sur ma photo et sur les photos d'Amazon, il se branche sur les 2 autres en face sur la 2ème ligne de picots (voir schéma joint).

Funciona bem foi só ligar ao raspberry apareceu logo imagem 5*

Ich habe dieses 5-Zoll-Touchscreen-Display von Waveshare für mein Raspberry‑Pi Projekt verwendet – und bin absolut überzeugt. Es liefert gestochen scharfe Bilder in 800×480 Auflösung und reagiert zuverlässig auf Eingaben. Die Installation ist kinderleicht: Einfach HDMI verbunden sowie USB für Touch angeschlossen – nach wenigen Sekunden erkennt das System den Touchscreen automatisch, ganz ohne zusätzliche Treiber. Ich habe es mit Raspberry Pi OS und diversen Linux-Varianten getestet, alles lief direkt und stabil. Der Touchscreen selbst ist robust: bei der DSI-Version handelt es sich um ein kapazitives Display mit gehärtetem Glas (5‑Punkte Touch, Härtegrad bis 6H), ideal für den täglichen Einsatz. Die HDMI‑Variante verfügt über resistiven Touch (single-point via SPI bzw. USB), funktioniert ebenfalls praxistauglich – für einfache Projekte völlig ausreichend.