Mouse Anti-Slip Tape Elastics Refined Side Grips Sweat Resistant Pads/Anti Sweat Paste Grip Tape Compatible for Razer Viper/Viper Ultimate Gaming Mouse

This works very well. The fit is very precise, with very tight tolerances (be slow and careful when applying them to the mouse to ensure a good alignment) The stock grip has a variable thickness, while this product has a uniform thickness. However, this product's thickness is PERFECT for the edges of the grip where it meets the body of the mouse, making for a seamless transition from grip to plastic with no ridge or groove. However, the uniform thickness means that areas where the stock grip was thicker become slightly dented feeling with this product, as it doesn't fill those deeper voids in the plastic quite as well as the stock grip. The most notable spot where I can feel a dent is right where my thumb sits though, so it's actually quite comfortable and a non-issue. Maybe even more ergonomic! I found that the stock grip was quite easy to remove by just picking the front corner up with a fingernail, and pulling the grip off the mouse. No heat was needed. I suppose if you have particularly weak hand grip strength, using heat might make it easier, but I had no trouble. Once the stock grip is peeled off, there is a thin foam-like residue left over that must be scraped off before applying this product. I recommend using a plastic spudger or other sharp plastic tool to avoid scarring the mouse plastic (a metal tool would damage the plastic). If you don't have a plastic spudger, add one to your order; they're super cheap, and worth the saved effort for scraping the residue off. When the residue has been mostly cleaned off, use isopropyl alcohol and paper towel to get any remaining bits, and clean off any oils that may be stuck on the plastic. When the surface is prepped, carefully (and slowly) line up the new grip with the back bottom corner of the mouse first, to ensure a seamless fit in that most critical and frequently touched area. For the click buttons, line up the little tab section in the middle first, and make sure you keep it straight as it goes on. Work along an edge, then move inwards to ensure good alignment. I skipped the thumb buttons, as other reviewers had mentioned it wears off quite fast; The stock mouse does not have grip there, and the thumb buttons endure constant sideways force as you lift the mouse during daily use, so it's a terrible place to put tape, as it will come right off. My mouse now looks absolutely fantastic and is so easy to lift compared to before with my worn grip. If I have any issues with peeling later, I'll come back and edit this review. So far so good!

So, I spilled a drink near my mouse, it still worked fine, but I found that one of the side buttons was sticking, so I needed to be able to open the mouse up and give it a deep clean. To do that, I needed to remove the stock feet. This set worked perfectly as a replacement. They have a precise fit, weren't too difficult to apply, and feel just as good, if not better than the originals (which admittedly were wearing a bit thin after 2+ years of use). It allowed me to resolve my sticky button issue, and even lube up the posts on the left and right mouse buttons to help alleviate the infamous "squeak". My mouse feels as good as new again and it saved me from needing to buy a whole new mouse. To anyone complaining about these not fitting, you need to read the description a little more carefully next time. This is for the Razer Viper ULTIMATE (the wireless version of the razer viper). Do NOT buy these for the wired Razer Viper or the Viper Mini - those are different products. To the person who thinks the feet feel like sandpaper on your mousepad - you need to remove the white protective stickers on each after you've applied them. I get that the instructions aren't very clear on the packaging, but it's pretty straight forward. NOTE: You WILL want to carefully examine the orientation of the foot in the middle that sits around the mouse sensor. At first glance it looks like you should be able to apply it either direction, but that's not the case. One end has more highly defined rounded corners - that end needs to be facing downwards, beneath the sensor.

I had to replace the original grips that came witht the razer viper ultimate. I bought these and they turned out great better the orignal grip. Easy instiliation. I love it so much, I perform better while playing video games

I got this to replace the worn out grip on my mouse. Could probably have just stuck it right over the old grip, but it'd been worn down so bad that the new tape just conformed to all the divots and looked terrible. I dug out the old grips and just put these new ones on the bare plastic and it's worked great for ... 9 months so far? The only thing that didn't work as well as I would have liked was the thumb buttons. Just because it's a small contact spot and the surface is curved, the thumb button tape came off after a while, but the main grip has held up very well!

These grips help my mouse feel more premium and provide grip during long gaming durations.

Fits perfectly on the Razer Viper Ultimate! I highly recommend it as a solution to the well-known Razer finger grip issue, especially for those whose skin tends to wear down the rubber material on older models. This tape provides a strong, firm grip while covering and protecting the original material on the mouse. It’s an excellent choice for gamers who want to maintain their trusty mouse in great condition. Totally worth it!

I use it for my razer mouse and it grips around the mouse just fine. You have to be extra careful because there is no tolerance at all for the sizing of the grips. You have to be able to match the exact edges of the grip to the mouse or else it looks weird. Which is fine by me because I do that anyway for most things but keep that mind if you want to be lazy about doing it. It's very grippy and definitely helps with my gaming sessions and such.

Compre este repuesto para mi mouse ya llevo meses con la compra y se ve impecable y al tacto se siente bien.

Change la vie

suite à l'ouverture de ma souris pour fixer un problème de click latéraux ces patins font le job je n'ai pas remaqué de différence notable avec ceux d'origine

Hanno ridato vita al mio mouse tutto usato unica diffetto potrebberro esserci dei mm di differenza del taglio

Tenia tiempo que un ratón no me duraba tanto (razer viper ultimate) por lo mismo las gomas laterales ya estaban desvanecidas hasta el plástico. Gracias a estos pads ha vuelto a la vida!! tamaño perfecto, buen grip.

Muy buenos agarres, se los puse cuando los compre, después de un tiempo, siguen agarrando bien, compre otro más para cuando estos acaben desgastandose poner los nuevos.