Mount-It! Universal Full Motion Steel Pole Mount with Articulating Arm and Removable VESA Plate for 17 to 32 Inch Monitors & TVs, VESA 75x75 & 100x100 Compatible, Black (MI-391)

This product is fabulous for its intended purposes. It is strong and pretty durable. However, for the use in a car it is not so great. Since its purposes is not vehicle application, it is not working out so great for me. Another reviewer said they used a stopper to make it work great on their headrest, but I can say from the experience of trying a rubber stopper, it did not work. It still drooped and sagged terribly. I am only trying to mount a 24" tv. So, no thanks given. I have to use a bungee cord in conjunction just to keep it held up in a useful position if I try to use it in the vehicle which I will not actually be doing with this mount. Just tried out of curiousity. I do have a place to use it for its intended purpose and it does work beautifully at my desk. I love that it can be manipulated in many directions and is very sturdy when mounted to a properly sized stable post. I would not hesitate to buy this again if I needed one, but this one looks like it will last forever. However, I am using a different type of mount for the tv in my vehicle now. Happy mounting!

This works well as a headrest mount for my car, a Chevrolet Suburban. It's not perfect, but it's the least bad solution I found. Taking inspiration from the other reviewer, I mounted this using a 1 5/8" black rubber stopper from Home Depot. I drilled a 1/2" hole into my 1 5/8" rubber stopper, and then cut a slit into the stopper from one edge into the newly drilled center hole. I also cut another slit a few millimeters over so that I could remove a small pie piece wedge. The idea was to make the stopper easier to fit onto the headrest mount -- not sure if it was a good idea or bad idea. I then installed the stopper onto the headrest (wider side down) -- it wasn't a perfect fit, but once I got the mount brackets over it, it held sturdily enough that I could tighten it down. To tighten down fully I used a 6mm hex bit attached to my drill/driver. I did not need to use any of the extension parts that the pole mount ships with. Things I learned: Do NOT use a neoprene stopper. They are very difficult to drill into / cut into, and compress too much such that the headrest would sag. Using a drill/driver with a 6mm hex bit makes this much easier to install. I only had imperial hex bits, so I bought the Tekton metric hex set available on Amazon. This will easily hold a 24" TV (specifically an ONN). You could probably do bigger, but even 24" feels plenty large in a Suburban. The arm on this mount is not long enough to perfectly center, but it's close enough.

Plastic, but since my garage TV is small and light, it works just fine! I also mounted a Roku Streambar SE under the TV, repurposing some of the included brackets and some tie-wraps. Tight!

Was used in a Peterbilt truck. To hold a 35” tv. It did very well. Didn’t have to put any holes on interior walls easy to install and uninstall

Worked great

I am a 65 year old women and this was easy for me to mount - quality is good and sturdy.

I ❤️this Clip-on TV Mount‼️My tall poles portable TV stand took up too much space in my small living room to rotate the TV screen to where I sit. I attached this Clip to one of the poles. Pushed stand back against wall and can rotate TV now.Poles on portable stand fit exactly right. Thank God I didn't have to purchase a pole. My TV stands poles has a capacity to hold 32" to 80" TVs. This MOUNT IT CLIP holds 32" to 55" inch TVs. I used only the equipment shipped. LUCKY, I only had to attach one piece to the back of my TV. I would have had to contact someone if my TV was bigger, to attach other parts. Please keep all the parts shipped cause you will need them, if your TV back is larger than 32" to 55" My "Mount It" does tilt TV up or down. Remember to tighten.🛑🛑🛑🛑CAUTION: AS DIRECTIONS STATE, 2 people to set TV up.

Why did you pick this product vs others?: Work great for my use. I bought these to attach joystick and throttle to my gaming chair. Don't currently have a picture as I've taken them off for a while since I haven't been flying, but if your chair has the arms like mine, it will work fantastically.

Buen producto, cumple su funcion

good

item excellent and super fast delivery

I may not be using these as intended but they are perfect for me. This is definitely the best Hotas or Hosas setup out there under 100$ I was worried that the oval armrest pole would be too big for the clamps but they can accommodate quite a large diameter pole. Very good stuff!

100% awesome